LAISHA
Open Laisha

Agricultural and Biosystems Engineers Licensure Examination Workshop Technology & Manufacturing: practice questions

Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC

Original practice questions written to the published syllabus · not past papers
10worked here, free
74written to this exam in this subject
12syllabus units

About Agricultural and Biosystems Engineers Licensure Examination

Agricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.

Source: prc.gov.ph.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Workshop Technology & Manufacturing in Agricultural and Biosystems Engineers Licensure Examination

Machinery fabrication within the power, energy and machinery subject: materials and their designations, welding and joint strength, machine-shop calculations, sheet-metal development and fabrication practice, solved with a non-programmable calculator.

How farm machines are made: joining, casting, machining, heat treatment and measurement, up to building a prototype.

Our 74 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 36 easy, 31 medium, 7 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.

Question 1 · easy

A 50 mm diameter shaft is turned at 300 rev/min. What is the cutting speed?

  1. 15.0 m/min
  2. 4712 m/min
  3. 47.1 m/min
  4. 94.2 m/min
Answer and working

C. 47.1 m/min

V = πDN/1000 = π × 50 × 300 / 1000 = 47.1 m/min. 15.0 omits π; 4712 takes the diameter in centimetres and leaves out the conversion to metres (π × 5 × 300; dropping the 1000 alone would give 47 124); 94.2 uses the diameter as a radius in 2πr.

Question 2 · medium

A taper runs from 50 mm to 40 mm diameter over 100 mm length. To what angle is the compound rest swivelled?

  1. 2.86°
  2. 5.71°
  3. 11.31°
  4. 1.43°
Answer and working

A. 2.86°

Half-angle α = tan⁻¹[(D − d)/2L] = tan⁻¹(10/200) = 2.86°. 5.71° is the included angle approximation (forgot the 2); 11.31° uses (D − d)/(L/2); 1.43° halves the half-angle again.

Question 3 · medium

On a centre lathe, why is the lead screw kept for thread cutting and not used for ordinary turning feeds?

  1. To preserve its accuracy, since wear from routine feeding would spoil cut threads
  2. Because it rotates too slowly to give any feed suitable for plain turning work
  3. Because it drives the cross slide only, and cannot move the carriage along the bed
  4. Because it is engaged by friction clutch and slips under normal turning loads
Answer and working

A. To preserve its accuracy, since wear from routine feeding would spoil cut threads

The lead screw's pitch accuracy determines the accuracy of the threads it cuts, so ordinary feeds are taken from the feed rod to save it from wear. It does move the carriage (through the half nut) and can rotate at any geared speed.

Question 4 · medium

A lathe has a lead screw of 6 mm pitch. A thread of 1.5 mm pitch is to be cut with simple change gears. Which driver/driven pair gives the right ratio?

  1. 80-tooth driver, 20-tooth driven
  2. 20-tooth driver, 80-tooth driven
  3. 30-tooth driver, 45-tooth driven
  4. 40-tooth driver, 60-tooth driven
Answer and working

B. 20-tooth driver, 80-tooth driven

Driver/driven = pitch to be cut / lead-screw pitch = 1.5/6 = 1/4, so 20/80. 80/20 gives 24 mm pitch; 30/45 and 40/60 both give 2/3, a 4 mm pitch.

Question 5 · easy

What spindle speed gives a cutting speed of 24 m/min with a 12 mm drill?

  1. 2000 rev/min
  2. 637 rev/min
  3. 6.37 rev/min
  4. 318 rev/min
Answer and working

B. 637 rev/min

N = 1000V/(πD) = 1000 × 24/(π × 12) = 637 rev/min. 2000 omits π; 6.37 omits the 1000; 318 doubles the diameter, as if 12 mm were the radius.

Question 6 · medium

A shaper is to machine a flat surface 150 mm wide with a cross feed of 0.5 mm per stroke at 30 strokes per minute. How long will it take?

  1. 5 min
  2. 20 min
  3. 300 min
  4. 10 min
Answer and working

D. 10 min

Strokes needed = 150/0.5 = 300; time = 300/30 = 10 min. 5 min and 20 min halve or double; 300 min confuses the number of strokes with minutes.

Question 7 · medium

What is the bend allowance for a 90° bend in 2 mm sheet with an inside radius of 5 mm, taking the neutral-axis factor k as 0.33?

  1. 9.42 mm
  2. 7.85 mm
  3. 11.0 mm
  4. 8.89 mm
Answer and working

D. 8.89 mm

BA = θ(R + kt) = (π/2)(5 + 0.33 × 2) = 8.89 mm. 9.42 mm puts the neutral axis at mid-thickness (k = 0.5); 7.85 mm uses the inside radius alone; 11.0 mm uses the outside radius.

Question 8 · easy

A drawing for a sheet-metal grain-bin panel states only '16 gauge'. Why should the thickness be given in millimetres instead?

  1. Gauge numbers differ between countries and between steel and non-ferrous sheet
  2. Gauge numbers apply only to wire, so they cannot describe sheet thickness at all
  3. Millimetre values are needed by law on every drawing made anywhere in the world
  4. A gauge number gives the sheet's width, not its thickness, in most catalogues
Answer and working

A. Gauge numbers differ between countries and between steel and non-ferrous sheet

Several gauge systems exist, and the same number gives different thicknesses for steel, galvanised steel and aluminium and in different countries, so the thickness is stated in mm. Gauges are used for sheet as well as wire, and a gauge number is a thickness, not a width.

Question 9 · easy

What does the number in the structural-steel designation S275 (EN 10025) refer to?

  1. Ultimate tensile strength of 275 MPa
  2. Minimum yield strength of 275 MPa
  3. Brinell hardness of 275
  4. Carbon content of 0.275%
Answer and working

B. Minimum yield strength of 275 MPa

Structural steels in EN 10025 are named by minimum yield strength in MPa for the thinnest thickness range. The Indian E250/E350 grades follow the same idea. Tensile strength, hardness and carbon are not what the number gives.

Question 10 · easy

Which international standard series sets general safety requirements for agricultural machinery, such as guarding of moving parts?

  1. ISO 286
  2. ISO 4254
  3. ISO 525
  4. ISO 3650
Answer and working

B. ISO 4254

ISO 4254 covers the safety of agricultural machinery (part 1 is general requirements). ISO 286 covers limits and fits, ISO 525 bonded abrasive products, and ISO 3650 gauge blocks.

A study plan for Workshop Technology & Manufacturing in Agricultural and Biosystems Engineers Licensure Examination

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 74 questions): Lathe operations (9, 12%); Casting processes (8, 11%); Drilling, milling and shaping (8, 11%); Specification of engineering materials (8, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Arc and gas welding (7, 9%); Fitting, carpentry and smithy (7, 9%); Metrology and measurement in the workshop (7, 9%); Press working of sheet metal (5, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Heat treatment of steels (4, 5%); Jigs, fixtures and gauges (4, 5%); Prototype fabrication (4, 5%); MIG and TIG welding and testing of welded joints (3, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Arc and gas welding (2 hard of 7), Drilling, milling and shaping (2 hard of 8), Metrology and measurement in the workshop (1 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Prototype fabrication (4 easy of 4); Heat treatment of steels (3 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Agricultural and Biosystems Engineers Licensure Examination Workshop Technology & Manufact

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.