ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)
Original practice questions written to the published syllabus · not past papersASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.
Official site: pw.live.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Manufacturing as listed in the discipline: process selection, materials for soil-engaging parts, heat treatment, welding and its testing, machining calculations (cutting speed, time, indexing), and fabrication of machinery.
How farm machines are made: joining, casting, machining, heat treatment and measurement, up to building a prototype.
Our 125 ASRB NET questions in this subject: 37 easy, 57 medium, 31 hard, across 12 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ASRB NET and are not shown on any other exam's page.
Which oxy-acetylene flame is normally used for welding or braze welding brass?
D. Oxidising flame
Brass contains zinc, which boils off and causes porosity; a slightly oxidising flame forms an oxide film that limits zinc fuming. A neutral flame suits steel. Carburising and reducing flames (the same thing, with excess acetylene) would worsen zinc loss.
Using the IIW formula, what is the carbon equivalent of a steel with 0.45% C, 0.75% Mn and negligible other alloying elements?
D. 0.575
CE = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15 = 0.45 + 0.75/6 = 0.45 + 0.125 = 0.575. 0.450 ignores manganese; 1.200 adds manganese at full weight; 0.700 divides manganese by 3. A value this high normally calls for preheat and low-hydrogen practice.
Why is the sprue of a gating system tapered, with its narrow end at the bottom?
C. The falling stream speeds up, so a narrowing sprue keeps it full and stops air being drawn in
Velocity rises as √(2gh) down the sprue; by continuity the area must fall or the stream separates from the walls, creating low pressure that aspirates air and sand. Choking the flow rate is done by the gating ratio, not by slowing in the sprue; draft and shrinkage are not the reason.
Which moulding-sand property allows steam and gases to escape from the mould when hot metal is poured?
D. Permeability
Permeability is the ability of the sand mass to pass gas; low permeability causes blowholes. Refractoriness resists high temperature, collapsibility lets the casting contract and the sand be knocked out, and green strength holds the moist mould together.
For a tool–work pair, Taylor's equation is VT^0.25 = 300 (V in m/min, T in min). What tool life is expected at 150 m/min?
D. 16 min
T = (C/V)^(1/n) = (300/150)^4 = 2⁴ = 16 min. 2 min treats life as proportional to the speed ratio; 4 min squares instead of raising to the fourth power; 1.19 min takes the 0.25 power instead of the 4th.
A shaper has a stroke of 200 mm and makes 30 cutting strokes per minute. The return stroke takes half the time of the cutting stroke. What is the average cutting speed?
A. 9 m/min
V = LN(1 + m)/1000 with m = return time / cutting time = 0.5: V = 200 × 30 × 1.5/1000 = 9 m/min. 6 m/min ignores the quick return; 12 m/min uses a 1:1 ratio; 18 m/min uses (1 + 1/m).
A part is located on two accurately bored holes using two pins. Why is one of the pins made as a diamond (relieved) pin?
C. It allows for centre-distance tolerance while still stopping rotation
Two full round pins would jam if the hole spacing varies within tolerance. The diamond pin is relieved along the line joining the holes, so it only stops rotation about the round pin. It is not about hardness, and foolproofing is a separate design requirement.
A forged high-carbon steel ploughshare has been hardened by quenching. What should follow before it is used in stony soil?
C. Tempering at a low to moderate temperature to restore toughness
As-quenched martensite is very hard but brittle and can shatter on stones; tempering trades a little hardness for toughness. Normalising and annealing would soften the share and lose the hardening, and as-quenched steel is at its least tough.
A 2 m length of 50 mm × 10 mm mild steel flat bar is needed for a prototype. Taking the density of steel as 7850 kg/m³, what is its mass?
D. 7.85 kg
Volume = 0.05 × 0.01 × 2 = 0.001 m³; mass = 7.85 kg. 78.5 and 0.785 kg are decimal slips; 3.93 kg uses 1 m.
Which of these belongs in the bill of materials for a prototype seed drill?
A. Each part's material specification, stock size, quantity and make-or-buy status
A bill of materials lists every part with its material, stock size, quantity and whether it is made or bought; it drives purchasing, cutting lists and costing. Test results, operating costs and staffing belong in other documents.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.