LAISHA
Open Laisha

ASRB NET Hydraulic Drives & Controls: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
43written to this exam in this subject
9syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Hydraulic Drives & Controls in ASRB NET

Lecturer- and licence-level understanding of components and circuits, standards for linkage and couplers, efficiency and heat calculations, and the reasons behind design choices.

Oil hydraulics on tractors and machines: pumps, motors, cylinders, valves and circuits.

Our 43 ASRB NET questions in this subject: 1 easy, 20 medium, 22 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · medium

A forestry contractor working beside a river is asked to use an environmentally acceptable hydraulic fluid. Under ISO 15380, a fluid classed HETG is based on

  1. synthetic esters made from alcohols and acids
  2. polyalkylene glycols that are soluble in water
  3. polyalphaolefins and related synthetic hydrocarbons
  4. natural triglycerides, that is, vegetable oils
Answer and working

D. natural triglycerides, that is, vegetable oils

ISO 15380 defines HETG (triglycerides, vegetable oils), HEES (synthetic esters), HEPG (polyglycols) and HEPR (polyalphaolefins and related hydrocarbons). Vegetable-based HETG fluids biodegrade well but oxidise faster and are sensitive to water, so change intervals are often shorter.

Question 2 · medium

An oil sample is reported with the ISO 4406 cleanliness code 20/18/15. Compared with a sample coded 17/15/12, the first sample has

  1. three more particles per millilitre in each size range
  2. roughly eight times as many particles in each size range
  3. particles about three micrometres larger on average
  4. roughly three times as many particles in each size range
Answer and working

B. roughly eight times as many particles in each size range

Each ISO 4406 scale number is a range of particle count per mL, and each step up roughly doubles the count. Three steps is 2³ ≈ 8 times as many particles. The numbers are not counts, not sizes, and three steps is not three times. The three positions refer to particles larger than 4, 6 and 14 µm(c).

Question 3 · medium

A hydrostatic transmission with a variable pump and a fixed motor, operating at a fixed maximum pressure, is best described as a

  1. constant-torque drive whose speed rises with pump displacement
  2. constant-power drive whose torque falls as the speed increases
  3. constant-speed drive whose torque rises with pump displacement
  4. constant-pressure drive whose power is independent of speed
Answer and working

A. constant-torque drive whose speed rises with pump displacement

With a fixed motor displacement, output torque = Vm·Δp/(2π) is fixed by the pressure limit, while speed follows pump flow; power therefore rises with speed. A fixed pump with a variable motor gives constant power, with torque falling as motor displacement is reduced to raise speed.

Question 4 · hard

A fixed pump delivers 40 L/min with the relief valve set at 140 bar. A meter-in flow control lets 15 L/min reach a cylinder whose load needs 80 bar; the rest crosses the relief valve. The total power converted to heat is

  1. 7.33 kW
  2. 5.83 kW
  3. 9.33 kW
  4. 1.50 kW
Answer and working

A. 7.33 kW

Pump output = 140 × 40/600 = 9.33 kW (pump pressure is at relief setting). Useful power = 80 × 15/600 = 2.00 kW. Heat = 9.33 − 2.00 = 7.33 kW, made of 5.83 kW over the relief and 1.50 kW across the flow control. Each of those parts alone is an incomplete answer, and 9.33 ignores the useful work.

Question 5 · medium

In a load-sensing valve bank serving several functions, the purpose of the shuttle valves in the signal network is to

  1. average the load pressures of all operating functions for the pump control
  2. pass the lowest load pressure so the pump never exceeds the minimum demand
  3. pass the highest working load pressure to the pump's load-sensing control
  4. isolate the steering circuit from all the other implement work sections
Answer and working

C. pass the highest working load pressure to the pump's load-sensing control

Shuttle valves compare pairs of pressures and pass the higher; cascaded, they deliver the highest load pressure to the pump so it can supply every function. Averaging or passing the lowest would starve the most heavily loaded function. Steering priority is handled by a priority valve.

Question 6 · medium

Mineral oil (ρ = 870 kg/m³, cp = 1.88 kJ/kg·K) passes through a relief valve from 140 bar to tank pressure without doing work. Assuming all the energy stays in the oil, its temperature rise is about

  1. 8560 °C
  2. 8.6 °C
  3. 0.86 °C
  4. 3.8 °C
Answer and working

B. 8.6 °C

ΔT = Δp/(ρ·cp) = 140 × 10⁵/(870 × 1880) = 8.6 °C. Using cp in kJ instead of J gives 8560; a bar-to-pascal slip gives 0.86; using water's cp (4.18 kJ/kg·K) gives 3.8.

Question 7 · medium

In an electronic hitch control system on a large tractor, the draft force is usually measured by

  1. a pressure transducer fitted in the tractor's rear brake circuit
  2. a radar unit measuring the tractor's true ground speed
  3. load pins, force sensors fitted in the lower-link mounting points
  4. a potentiometer on the operator's draft-setting lever
Answer and working

C. load pins, force sensors fitted in the lower-link mounting points

Electronic draft control measures lower-link force with load pins that sense shear or bending. A rockshaft position sensor provides the position signal; radar ground speed is used for slip control; the lever potentiometer gives the set-point, not the measured draft.

Question 8 · hard

An electronic hitch has slip control enabled at 15 % wheel slip. While ploughing, slip rises to 20 % on a wet patch. The system responds by

  1. raising the implement slightly to cut draft until slip falls back below the limit
  2. lowering the implement to increase the weight transferred to the rear wheels
  3. engaging the differential lock and leaving the implement height unchanged
  4. reducing the engine speed so the wheels turn more slowly and grip better
Answer and working

A. raising the implement slightly to cut draft until slip falls back below the limit

Slip control compares driven-wheel speed with true ground speed (from radar or GNSS); when slip exceeds the set limit the hitch is raised a little to reduce draft. Lowering would raise draft and slip further. Differential lock and engine-speed management are separate functions.

Question 9 · hard

Ride control on a tractor carrying a heavy mounted implement on the road works by

  1. using the linkage as an active damper, moving it against the pitching motion of the tractor
  2. locking the lift cylinder hydraulically so that the implement cannot move relative to the tractor
  3. switching the linkage to float so that the implement's own weight steadies the tractor
  4. reducing the engine speed automatically whenever the front axle load falls below a limit
Answer and working

A. using the linkage as an active damper, moving it against the pitching motion of the tractor

Ride control senses pitching and moves the linkage, often against an accumulator or through valve control, to absorb and counteract the bounce, improving steering contact and comfort. A hydraulic lock transmits every shock, float would drop the implement, and engine-speed control is unrelated.

Question 10 · easy

Which pump type is most tolerant of moderately contaminated oil and is therefore common on low-cost implements and small tractors?

  1. Axial-piston pump
  2. Radial-piston pump
  3. External gear pump
  4. Unbalanced vane pump
Answer and working

C. External gear pump

Gear pumps have robust geometry and tolerate dirt better than piston or vane pumps, whose close-fitting pistons, shoes and vane tips are damaged quickly by particles. That, with low cost, is why they dominate open-centre systems. Contamination tolerance does not excuse poor filtration.

A study plan for Hydraulic Drives & Controls in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 43 questions): Hydraulic pumps: gear, vane and piston (6, 14%); Open-centre, closed-centre and load-sensing circuits (6, 14%); Pressure relief and flow control valves (6, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Tractor hydraulic systems (6, 14%); Hydraulic motors (5, 12%); Principles of fluid power (5, 12%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Hydraulic cylinders (4, 9%); Directional control valves (3, 7%); Pressure drop and heat generation (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Hydraulic cylinders (4 hard of 4), Pressure relief and flow control valves (4 hard of 6), Directional control valves (2 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Hydraulic pumps: gear, vane and piston (1 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Hydraulic Drives & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.