LAISHA
Open Laisha

Rajasthan PSC Hydraulic Drives & Controls: practice questions

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
41written to this exam in this subject
9syllabus units

About Rajasthan PSC

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.

Source: rpsc.rajasthan.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Hydraulic Drives & Controls in Rajasthan PSC

Oil hydraulics on tractors and machines: pumps, motors, cylinders, valves and circuits.

Our 41 Rajasthan PSC questions in this subject: 17 easy, 20 medium, 4 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Rajasthan PSC and are not shown on any other exam's page.

Question 1 · easy

A tractor works in a region where it starts at −5 °C in the morning and runs at high oil temperature by afternoon. Which property of the hydraulic fluid matters most for keeping viscosity acceptable across this range?

  1. A high flash point
  2. A high bulk modulus figure
  3. A high viscosity index
  4. A high specific gravity
Answer and working

C. A high viscosity index

The viscosity index describes how little the viscosity changes with temperature; a high-VI fluid stays thin enough to pump at a cold start and thick enough to seal when hot. Flash point concerns fire risk, bulk modulus concerns stiffness, and specific gravity concerns density, none of which controls viscosity change with temperature.

Question 2 · hard

A pump on an older tractor makes a loud gravelly, rattling noise on cold mornings that fades as the oil warms. The oil does not look foamy. The most likely cause is

  1. cavitation, with thick cold oil starving the inlet
  2. aeration from an air leak in the pump pressure line
  3. a relief valve set too high for the circuit's rating
  4. a worn pump with high internal leakage at pressure
Answer and working

A. cavitation, with thick cold oil starving the inlet

Cold, viscous oil raises suction losses, so inlet pressure falls below the vapour and air-release level and bubbles collapse violently as they reach the outlet: cavitation, with its gravelly noise. Aeration usually gives foamy oil and a whine, and comes from leaks on the suction side, since a pressure-line leak sprays oil out rather than drawing air in. A high relief setting or a worn pump does not produce noise that fades as oil warms.

Question 3 · medium

In a closed-loop hydrostatic transmission on a self-propelled sprayer, the charge pump's job is to

  1. keep the low-pressure side above a set minimum and make up leakage losses
  2. provide the main high-pressure flow that drives the wheel motors at full speed
  3. relieve pressure peaks on the high-pressure side when the machine is braking
  4. return the case-drain oil to the main loop without passing through the cooler
Answer and working

A. keep the low-pressure side above a set minimum and make up leakage losses

In a closed loop the motor returns oil directly to the pump inlet, so leakage to the cases must be made up and the low side must be kept pressurised to prevent cavitation; the charge pump does both and brings in filtered, cooled oil. The main pump drives the motors, crossover relief valves deal with pressure peaks, and case drains go through the cooler to the reservoir.

Question 4 · easy

A tipping-trailer cylinder with a 100 mm bore and a 500 mm stroke is extended by a tractor remote supplying 25 L/min. Neglecting compressibility and leakage, the time to extend fully is about

  1. 9.4 s
  2. 0.157 s
  3. 37.7 s
  4. 2.36 s
Answer and working

A. 9.4 s

Swept volume = π(0.1)²/4 × 0.5 = 3.927 L. Time = 3.927/25 min = 0.1571 min = 9.4 s. 0.157 is the time in minutes written as seconds; treating the bore as a radius gives 37.7; 2.36 uses half the bore as the diameter.

Question 5 · easy

In an open-centre tractor hydraulic system with all control valves in neutral,

  1. pump flow returns to tank at low pressure through the valve centres
  2. the pump stands by at high pressure while delivering almost no flow
  3. pump flow passes over the main relief valve and back to the tank
  4. the pump is unloaded by an accumulator and an external pilot valve
Answer and working

A. pump flow returns to tank at low pressure through the valve centres

Open-centre valves have a through passage in neutral, so a fixed pump circulates its full flow to tank at only the pressure needed to overcome line and valve losses. High standby pressure with no flow describes a pressure-compensated closed-centre system; flow over the relief would overheat the oil; accumulator unloading is a different closed-centre arrangement.

Question 6 · easy

On a tractor whose single pump supplies both power steering and implement hydraulics, which valve ensures the steering is always supplied first?

  1. A pressure-reducing valve
  2. A counterbalance valve
  3. A priority flow-control valve
  4. A pilot-operated check valve
Answer and working

C. A priority flow-control valve

A priority valve sends the flow the steering demands to the steering circuit first and passes the excess to the other functions. A reducing valve limits branch pressure, a counterbalance valve holds an overrunning load, and a pilot-operated check holds a cylinder.

Question 7 · easy

Which linkage control mode is most suitable for a mounted boom sprayer, which must stay at a set height above the crop?

  1. Draft control
  2. Float control
  3. Position control
  4. Intermix control
Answer and working

C. Position control

Position control holds the implement at a fixed height relative to the tractor regardless of load, which is what a sprayer, mower or transport needs. Draft control would move the boom as forces changed, float lets it drop to the ground, and intermix blends in a draft signal the sprayer does not need.

Question 8 · easy

A tractor's lift cylinder takes in 1.2 L of oil to raise the linkage from fully down to fully up. The pump supplies 30 L/min to the lift. The time to raise the linkage fully is about

  1. 0.04 s
  2. 2.4 s
  3. 25 s
  4. 144 s
Answer and working

B. 2.4 s

t = V/Q = 1.2 L/30 L/min = 0.04 min = 2.4 s. 0.04 is the time in minutes; 25 is Q/V; 144 multiplies by 3600 instead of 60.

Question 9 · medium

Larger tractors with closed-centre load-sensing hydraulics commonly use which type of main pump?

  1. Fixed-displacement external gear pump
  2. Fixed-displacement balanced vane pump
  3. Single-stage centrifugal pump
  4. Variable-displacement axial-piston pump
Answer and working

D. Variable-displacement axial-piston pump

Load sensing needs a pump whose displacement can be varied by its LS compensator, usually a swash-plate axial-piston pump. Gear and balanced vane pumps are fixed-displacement and are used in open-centre systems; centrifugal pumps are not positive-displacement and are not used for power hydraulics.

Question 10 · medium

Which is the safest practice when a farmer needs to work under a mounted rotary tiller held up on the tractor's three-point linkage?

  1. Keep the engine running so the pump maintains pressure in the lift cylinder throughout
  2. Set the linkage to position control at full height, which locks it hydraulically for work
  3. Lower it onto solid stands so it is held mechanically, never by hydraulics alone
  4. Close the drop-rate valve fully, which holds the implement safely for any length of time
Answer and working

C. Lower it onto solid stands so it is held mechanically, never by hydraulics alone

Hydraulic holding can fail through valve leakage, a burst hose or someone touching a lever; only mechanical support is safe. A running pump, position control or a closed drop-rate valve all still rely on hydraulics, and spool valves leak.

A study plan for Hydraulic Drives & Controls in Rajasthan PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 41 questions): Tractor hydraulic systems (11, 27%); Principles of fluid power (6, 15%); Hydraulic cylinders (5, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Open-centre, closed-centre and load-sensing circuits (5, 12%); Hydraulic motors (4, 10%); Hydraulic pumps: gear, vane and piston (3, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Pressure relief and flow control valves (3, 7%); Directional control valves (2, 5%); Pressure drop and heat generation (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Hydraulic pumps: gear, vane and piston (2 hard of 3), Hydraulic cylinders (1 hard of 5), Tractor hydraulic systems (1 hard of 11).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Pressure relief and flow control valves (2 easy of 3); Open-centre, closed-centre and load-sensing circuits (3 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Rajasthan PSC Hydraulic Drives & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.