LAISHA
Open Laisha

Rajasthan PSC Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing: practice questions

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
42written to this exam in this subject
15syllabus units

About Rajasthan PSC

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.

Source: rpsc.rajasthan.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in Rajasthan PSC

Sprayers, weeders, mowers, reapers, combines and threshers: how they work, how to calibrate them and where losses come from.

Our 42 Rajasthan PSC questions in this subject: 32 easy, 8 medium, 2 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Rajasthan PSC and are not shown on any other exam's page.

Question 1 · easy

In a hydraulic sprayer, strainers are made progressively finer from the tank filling opening towards the nozzle so that

  1. the pump runs at lower speed
  2. the tank agitates faster
  3. pressure at the nozzle rises as each finer screen accelerates the flow towards the tip
  4. the smallest opening in the system, the nozzle orifice, does not block
Answer and working

D. the smallest opening in the system, the nozzle orifice, does not block

Coarse strainers stop large debris early; the finest strainer is just before the nozzle, which has the smallest orifice. Strainers do not raise pressure; they cause a small pressure drop.

Question 2 · easy

In the field, the sprayer's forward speed for calibration should be found by

  1. reading the tractor speedometer on a smooth road at the same gear and engine speed
  2. timing the sprayer over a measured distance in the field to be sprayed
  3. calculating from engine rpm and gear ratio alone
  4. asking the operator
Answer and working

B. timing the sprayer over a measured distance in the field to be sprayed

Wheel slip and soft or uneven ground change actual speed, so the reliable value comes from timing a measured run in the field. For example, 100 m in 60 s is 100/60 × 3.6 = 6 km/h.

Question 3 · easy

In a hand-operated rotary duster, the air stream is produced by

  1. a fan driven at high speed by a crank through a gear train
  2. a piston pump
  3. a bellows squeezed by hand at each stroke of the operating lever
  4. compressed gas cartridge
Answer and working

A. a fan driven at high speed by a crank through a gear train

The rotary duster uses a crank and step-up gears to spin a fan; the same drive usually turns the hopper agitator. Bellows and plunger dusters are separate types.

Question 4 · easy

On a standard reciprocating cutter bar, the knife stroke, section spacing and guard spacing are each

  1. 76.2 mm
  2. 50.8 mm
  3. 101.6 mm
  4. 38.1 mm
Answer and working

A. 76.2 mm

The standard cutter bar uses a 3 in (76.2 mm) stroke with sections and guards at 76.2 mm spacing, so each section moves from one guard centre to the next. 50.8 mm (2 in) and 101.6 mm (4 in) are not the standard; 38.1 mm is the crank radius, half the stroke.

Question 5 · easy

A vertical conveyor reaper (VCR)

  1. cuts, threshes and cleans the crop in one pass
  2. cuts the crop and conveys it upright to one side, laying it in a windrow
  3. cuts the crop and ties it into bundles with twine, dropping them in a row behind
  4. strips grain heads from standing straw
Answer and working

B. cuts the crop and conveys it upright to one side, laying it in a windrow

The VCR's lugged belts carry the cut stems across and drop them in a windrow at right angles to travel. Binding is done by a reaper-binder; threshing by a combine; stripping by a stripper header.

Question 6 · easy

Loss of grain that has fallen to the ground from over-ripe crop before the harvester arrives is called

  1. cleaning loss
  2. separation (walker) loss
  3. threshing loss
  4. pre-harvest (shattering) loss
Answer and working

D. pre-harvest (shattering) loss

It occurs before any machine action and grows as harvest is delayed. The other losses arise inside the combine.

Question 7 · easy

Of 1000 kg/h of grain fed to a thresher, 8 kg/h leaves still in the heads. The threshing efficiency is

  1. 92%
  2. 0.8%
  3. 99.92%
  4. 99.2%
Answer and working

D. 99.2%

Threshing efficiency = 100 − unthreshed % = 100 − (8/1000 × 100) = 99.2%. 0.8% is the unthreshed fraction. 92% subtracts the 8 kg directly from 100; 99.92% divides by 100 instead of 1000 in the unthreshed fraction.

Question 8 · medium

To obtain a shorter length of cut on a chaff cutter at the same flywheel speed, the operator should

  1. increase the feed roll speed
  2. remove one knife
  3. widen the knife-to-shear-plate clearance
  4. reduce the feed roll speed through the gearbox
Answer and working

D. reduce the feed roll speed through the gearbox

Length of cut = feed speed / cuts per second; slower feed rolls give shorter pieces. Removing a knife would double the length. Wider clearance gives ragged cuts.

Question 9 · easy

In an elevator-type potato digger, soil is separated from tubers mainly by

  1. washing with water jets that are sprayed onto the lifted mass as it passes over the rear of the elevator
  2. air blowing
  3. magnetic separation
  4. passing the lifted mass over a rod-link elevator that is agitated so loose soil falls through
Answer and working

D. passing the lifted mass over a rod-link elevator that is agitated so loose soil falls through

The share lifts soil and tubers onto the rod-chain elevator; agitators shake soil through the gaps and tubers are dropped on the surface.

Question 10 · easy

The primary extractor fan on a sugarcane harvester

  1. cuts the cane at the base
  2. lifts lodged cane
  3. loads cane into the mill
  4. removes trash
Answer and working

D. removes trash

It removes extraneous matter after chopping; setting its speed trades trash removal against cane loss. The fan blows leaves and trash out of the cane stream.

A study plan for Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in Rajasthan PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 42 questions): Sprayer calibration and application rate (5, 12%); Threshers (4, 10%); Weeders and inter-cultivation equipment (4, 10%); Combine harvester: header, threshing cylinder and concave (3, 7%); Dusters (3, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Harvesting and threshing losses (3, 7%); Sprayers: hydraulic, air-assisted and electrostatic (3, 7%); Straw and residue management machines (3, 7%); Chaff cutters (2, 5%); Combine separation and cleaning: straw walker and cleaning shoe (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Cotton and sugarcane harvesting (2, 5%); Mowers: reciprocating and rotary; mechanics of cutting (2, 5%); Nozzles and droplet spectra (2, 5%); Reapers (2, 5%); Root-crop diggers (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Straw and residue management machines (1 hard of 3), Threshers (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Combine harvester: header, threshing cylinder and concave (3 easy of 3); Sprayers: hydraulic, air-assisted and electrostatic (3 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Rajasthan PSC Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.