LAISHA
Open Laisha

Rajasthan PSC Mechanics of Tillage & Traction (Soil Dynamics): practice questions

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
29written to this exam in this subject
13syllabus units

About Rajasthan PSC

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.

Source: rpsc.rajasthan.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mechanics of Tillage & Traction (Soil Dynamics) in Rajasthan PSC

Traction and CG determination named in the farm power syllabus; direct formula questions.

How soil resists tools and supports wheels: draft, slip, tractive efficiency, weight transfer and stability.

Our 29 Rajasthan PSC questions in this subject: 24 easy, 5 medium, 0 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Rajasthan PSC and are not shown on any other exam's page.

Question 1 · easy

In a disc harrow, why are the front gangs set at opposite angles?

  1. To increase the side draft for better soil inversion
  2. So that their side forces largely cancel
  3. To reduce the vertical load on the discs to roughly zero
  4. To allow the harrow to work without any draft
Answer and working

B. So that their side forces largely cancel

Each angled gang produces a side force; opposing gangs balance them so the harrow runs straight. Vertical load is still needed for penetration, and draft cannot be zero.

Question 2 · easy

A 3 m wide tine cultivator has a unit draft of 2.5 kN per metre width. It is pulled at 6 km/h. What drawbar power does it need?

  1. 12.50 kW
  2. 45.00 kW
  3. 4.17 kW
  4. 4.50 kW
Answer and working

A. 12.50 kW

Draft = 2.5 × 3.0 = 7.5 kN. Power = 7.5 × 6/3.6 = 12.50 kW. Using unit draft without multiplying by width gives 4.17 kW. 45.00 kW multiplies by km/h without converting; 4.50 kW divides the draft by the speed (7.5/1.667).

Question 3 · easy

An engine delivers 40 kW; transmission efficiency is 0.90 and tractive efficiency 0.70. What drawbar power is available?

  1. 28.0 kW
  2. 63.5 kW
  3. 25.2 kW
  4. 36.0 kW
Answer and working

C. 25.2 kW

Drawbar = 40 × 0.9 × 0.7 = 25.2 kW. Ignoring the transmission gives 28.0 kW; dividing gives more than engine power, which is impossible. Dividing gives 63.5 kW; 36.0 kW ignores the tractive efficiency.

Question 4 · easy

A rollover protective structure (ROPS) protects the operator only if

  1. the tractor has four-wheel drive
  2. the tractor is fitted with front ballast
  3. the seat belt is worn so the operator stays within the protected zone
  4. the ROPS is folded down during field work to lower the centre of gravity
Answer and working

C. the seat belt is worn so the operator stays within the protected zone

In an overturn an unbelted operator can be thrown out and crushed by the ROPS or tractor. ROPS and seat belt work together; a folded ROPS gives no protection.

Question 5 · easy

A level tractor weighs 32 kN in total and its front axle reads 9.6 kN on a platform scale. The wheelbase is 2.4 m. How far ahead of the rear axle is the CG?

  1. 0.72 m
  2. 1.68 m
  3. 0.30 m
  4. 1.03 m
Answer and working

A. 0.72 m

Moments about the rear axle: Wf·L = W·x → x = 9.6 × 2.4/32 = 0.72 m. Using the rear reading gives the distance from the front axle, 1.68 m. 0.30 m forgets to multiply by L; 1.03 m divides by the rear reading (22.4 kN) instead of the total.

Question 6 · easy

A tractor with a track width of 1.5 m weighs 28 kN. The right-side wheels carry 14.7 kN. How far is the CG from the left wheel line?

  1. 0.713 m
  2. 0.750 m
  3. 0.787 m
  4. 0.394 m
Answer and working

C. 0.787 m

Moments about the left wheel line: W_right × t = W × y → y = 14.7 × 1.5/28 = 0.787 m, slightly right of centre (0.037 m). Using the left reading gives the distance from the right wheel line. 0.713 m uses the left reading; 0.750 m assumes the CG is central; 0.394 m uses half the track.

Question 7 · easy

Of several passes of the same wheel in one track, which usually causes the largest increase in bulk density?

  1. The last pass in the track
  2. The first pass
  3. The passes are equal
  4. The third pass, once the soil has been loosened
Answer and working

B. The first pass

Most compaction occurs on the first pass; later passes add less each time but push compaction deeper. This is why confining traffic to fewer tracks helps.

Question 8 · medium

The coefficient of rolling resistance of a towed wheel is

  1. wheel load divided by the rolling resistance
  2. rolling resistance divided by drawbar pull
  3. rolling radius divided by unloaded radius
  4. rolling resistance divided by wheel load
Answer and working

D. rolling resistance divided by wheel load

RR/W is a dimensionless coefficient; it is small on firm roads and several times larger on soft or tilled soil.

Question 9 · medium

Which change improves the lateral stability of a tractor working across slopes?

  1. Setting the rear wheels to a wider track
  2. Raising a mounted implement to full height
  3. Removing liquid ballast from the rear tyres
  4. Filling a front loader bucket and raising it
Answer and working

A. Setting the rear wheels to a wider track

Lateral stability depends on half track over CG height. A wider track increases the base; raising loads or removing low ballast raises the CG.

Question 10 · easy

Compared with a wheeled tractor, a crawler tractor of the same weight has

  1. a smaller contact area and higher mean ground pressure
  2. the same contact area
  3. no rolling resistance
  4. a larger contact area and lower mean ground pressure
Answer and working

D. a larger contact area and lower mean ground pressure

Tracks spread the load along a long contact length. They still have motion resistance from soil deformation and internal running-gear friction.

A study plan for Mechanics of Tillage & Traction (Soil Dynamics) in Rajasthan PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 29 questions): Longitudinal and lateral stability (4, 14%); Cone index and cone penetrometer (3, 10%); Traction theory: slip, rolling resistance and net traction (3, 10%); Wheel and track mechanics (3, 10%); Determination of the centre of gravity (2, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Prediction of draft (2, 7%); Soil compaction by vehicles (2, 7%); Traction in wetland soils (2, 7%); Tractive efficiency (2, 7%); Tractor chassis mechanics (2, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Weight transfer (2, 7%); Dynamic properties and strength of soil (1, 3%); Soil-tool mechanics (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Wheel and track mechanics (3 easy of 3); Determination of the centre of gravity (2 easy of 2).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Rajasthan PSC Mechanics of Tillage & Traction (Soil Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.