Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India.
Format
Objective paper; the paper structure was not captured.
Sections
Surveying, levelling and land development
Soil and water conservation (including Rajasthan structures: khadin, tanka, nadi, anicut)
Irrigation, drainage, pumps and water resources
Farm power and machinery (including SMAM and custom hiring centres in Rajasthan)
How it has changed
Syllabus dated 11/09/2025. Like every state PSC, it localises: state schemes and traditional structures carry marks. Other state PSCs set their own syllabi.
How to prepare for Rajasthan PSC
Where our 707 questions for it fall
Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.
2. Which set of works forms the core of on-farm development under command area development?
Tubewell electrification and crop insurance
Main canal lining and headworks gates
Construction of the main dam and spillway
Field channels, field drains, land levelling and shaping, and realignment of field boundaries
Answer and working
D. Field channels, field drains, land levelling and shaping, and realignment of field boundaries
On-farm development works are below the outlet: field channels, drains, levelling and shaping. Dams, headworks and main canal lining are part of the main system, and insurance is not a CAD work.
Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) · Command area development
3. A contour map has a contour interval of 2 m and the horizontal equivalent between two contours is 50 m. What is the ground slope?
4% (1 in 25)
25% (1 in 4)
2% (1 in 50)
0.04% (1 in 2500)
Answer and working
A. 4% (1 in 25)
Slope = CI / HE = 2/50 = 0.04 = 4%, i.e. 1 in 25. Inverting gives 25%; 2% divides 1 by 50, ignoring the 2 m interval; 0.04% is the ratio 0.04 written as a percentage without multiplying by 100.
Surveying & Levelling · Contouring
4. For a given discharge in an open channel, what is true of the flow at critical depth?
The specific energy is a maximum
The specific energy is a minimum
The Froude number is zero
The velocity head equals the depth
Answer and working
B. The specific energy is a minimum
On the specific-energy curve for a fixed q, the critical depth is the point of minimum E; equivalently, for a fixed E, discharge is maximum there. In a rectangular channel the velocity head at critical depth is y_c/2, not y_c, and Fr = 1.
Fluid Mechanics & Open Channel Hydraulics · Specific energy and critical depth
5. Two 12 V, 100 Ah batteries are connected in series for a 24 V starting system. The combination provides
12 V at 200 Ah
24 V at 200 Ah
12 V at 100 Ah
24 V at 100 Ah
Answer and working
D. 24 V at 100 Ah
In series the voltages add and the ampere-hour capacity stays the same. In parallel the capacity would add (12 V, 200 Ah).
Tractor & Automotive Engines (IC Engines) · Ignition and electrical system: battery, starter and alternator
6. Standard Test Conditions (STC) for rating PV modules are:
1367 W/m², 25 °C ambient temperature, air mass 0
1000 W/m² irradiance, 25 °C cell temperature, air mass 1.5
800 W/m², 20 °C ambient temperature, 1 m/s wind
1000 W/m², 45 °C cell temperature, air mass 2
Answer and working
B. 1000 W/m² irradiance, 25 °C cell temperature, air mass 1.5
STC is 1000 W/m², 25 °C cell temperature and AM1.5 spectrum. 800 W/m² with 20 °C ambient and 1 m/s wind are conditions used for nominal operating cell temperature, not STC.
Farm Power Sources · Solar power as a farm power source
7. In an open-centre tractor hydraulic system with all control valves in neutral,
pump flow returns to tank at low pressure through the valve centres
the pump stands by at high pressure while delivering almost no flow
pump flow passes over the main relief valve and back to the tank
the pump is unloaded by an accumulator and an external pilot valve
Answer and working
A. pump flow returns to tank at low pressure through the valve centres
Open-centre valves have a through passage in neutral, so a fixed pump circulates its full flow to tank at only the pressure needed to overcome line and valve losses. High standby pressure with no flow describes a pressure-compensated closed-centre system; flow over the relief would overheat the oil; accumulator unloading is a different closed-centre arrangement.
Hydraulic Drives & Controls · Open-centre, closed-centre and load-sensing circuits
8. A tractor has separate left and right brake pedals. Before travelling on a public road, the pedals should be latched together because
the latch adds hydraulic assistance that can only work on the road
braking one side alone at speed can swing the tractor sideways
an unlatched pedal disengages the differential lock automatically
road rules require the parking brake to be built into the latch
Answer and working
B. braking one side alone at speed can swing the tractor sideways
Independent pedals are for tight turning in the field. At road speed a one-sided brake application yaws the tractor and can overturn it, so the pedals are latched. The latch does not add assistance, does not affect the differential lock, and is not the parking brake.