LAISHA
Open Laisha

ICAR AIEEA-PG Mechanics of Tillage & Traction (Soil Dynamics): practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
49written to this exam in this subject
13syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mechanics of Tillage & Traction (Soil Dynamics) in ICAR AIEEA-PG

Unit V farm machinery and power: definitions of slip, tractive efficiency, rolling resistance, cone index, weight transfer and stability, with short calculations.

How soil resists tools and supports wheels: draft, slip, tractive efficiency, weight transfer and stability.

Our 49 ICAR AIEEA-PG questions in this subject: 30 easy, 17 medium, 2 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

As the rake angle of a narrow tine is increased from 30° to 90°, draft at a fixed depth generally

  1. decreases steadily
  2. stays constant because draft depends only on depth
  3. first falls to zero, then rises
  4. increases
Answer and working

D. increases

A steeper face pushes soil forward and must overcome more passive resistance, so draft rises with rake angle. Low rake angles lift soil gently at lower draft.

Question 2 · easy

An implement with a draft of 8.10 kN is pulled at 5.0 km/h. What drawbar power does it require?

  1. 40.50 kW
  2. 15.08 kW
  3. 145.80 kW
  4. 11.25 kW
Answer and working

D. 11.25 kW

P = D × v = 8.10 kN × (5.0/3.6) m/s = 11.25 kW. Multiplying by km/h without converting gives 40.50; dividing by 0.746 converts to horsepower, not kW. 15.08 kW divides by 0.746; 145.80 kW multiplies by 3.6 instead of dividing.

Question 3 · easy

A tractor covers a marked distance in 17 drive-wheel revolutions without load and in 20 revolutions when pulling a plough. What is the slip?

  1. 17.6 %
  2. 85.0 %
  3. 8.1 %
  4. 15.0 %
Answer and working

D. 15.0 %

s = 1 − N0/N1 = 1 − 17/20 = 15.0 %. Using (N1 − N0)/N0 = 17.6 % is the common wrong basis: slip is referred to the loaded revolutions (theoretical travel). 85.0 % is N0/N1 itself; 8.1 % divides the difference by the sum of the revolutions.

Question 4 · hard

In 10 revolutions a drive wheel travels 46 m in the no-load condition and 40 m under load. Find the slip and the rolling radius.

  1. 15.0 % and 0.732 m
  2. 13.0 % and 0.732 m
  3. 13.0 % and 0.637 m
  4. 13.0 % and 1.464 m
Answer and working

B. 13.0 % and 0.732 m

s = 1 − L1/L0 = 1 − 40/46 = 13.0 %. Rolling radius from the reference condition: 46/10 = 4.6 m per revolution; r = 4.6/(2π) = 0.732 m. Using loaded travel gives 0.637 m, which is not the reference; dividing by π gives the diameter.

Question 5 · medium

Why must the rolling radius, not the unloaded tyre radius, be used when calculating theoretical speed for slip?

  1. The unloaded radius is smaller than the effective radius, so it understates theoretical speed and therefore understates the slip
  2. The two are always equal on agricultural tyres
  3. The unloaded radius is larger than the effective radius, so it overstates theoretical speed and therefore overstates slip
  4. Slip is independent of the radius used
Answer and working

C. The unloaded radius is larger than the effective radius, so it overstates theoretical speed and therefore overstates slip

Distance per revolution on the reference surface defines the effective (rolling) radius, which is less than the unloaded radius because the tyre deflects. Using the larger radius inflates vt and hence s.

Question 6 · easy

A two-wheel-drive tractor with wheelbase 2.2 m pulls a horizontal drawbar load of 20 kN at a hitch height of 0.5 m. How much weight is transferred from the front to the rear axle?

  1. 88.0 kN
  2. 10.0 kN
  3. 2.27 kN
  4. 4.55 kN
Answer and working

D. 4.55 kN

ΔW = P·h/L = 20 × 0.5/2.2 = 4.55 kN. Inverting h and L gives 88.0 kN; forgetting to divide by L gives a moment, not a force. 10.0 kN is the moment P·h; 2.27 kN halves the transfer.

Question 7 · medium

A tractor weighs 30 kN with CG 0.8 m ahead of the rear axle. Ignoring rolling resistance, what horizontal drawbar pull at 0.6 m height would reduce the front axle load to zero on level ground?

  1. 40 kN
  2. 22.5 kN
  3. 24 kN
  4. 10.9 kN
Answer and working

A. 40 kN

Rf = (W x − P h)/L = 0 → P = W x/h = 30 × 0.8/0.6 = 40 kN. In practice slip limits pull well before this, but a stuck wheel or high hitch changes the picture. 22.5 kN inverts x and h; 24 kN is the moment W·x; 10.9 kN uses the wheelbase in place of the hitch height.

Question 8 · medium

A 2WD tractor weighing 32 kN (CG 0.85 m ahead of rear axle, wheelbase 2.3 m) pulls 16 kN horizontally at 0.55 m height on level ground. Find the dynamic rear axle reaction.

  1. 24.00 kN
  2. 8.00 kN
  3. 20.17 kN
  4. 40.00 kN
Answer and working

A. 24.00 kN

Moments about rear contact: Rf = (W x − P h)/L = (32 × 0.85 − 16 × 0.55)/2.3 = 8.00 kN. Rr = W − Rf = 24.00 kN. 8.00 kN is the front reaction; 20.17 kN is the static rear load. 40.00 kN adds the drawbar pull to the rear reaction.

Question 9 · easy

Why are cage wheels used on power tillers in puddled rice fields?

  1. They sink through soft mud to the firmer layer, grip it with lugs and do not clog with mud
  2. They float on the mud surface without sinking
  3. They reduce the power required for puddling to zero
  4. They increase the wheel's rolling radius on dry roads, so the tiller travels faster between fields
Answer and working

A. They sink through soft mud to the firmer layer, grip it with lugs and do not clog with mud

Cage wheels are open, lugged steel wheels; they reach the hardpan and engage it while shedding mud. Floats, not cage wheels, carry weight on the surface.

Question 10 · easy

A two-wheel trailer carrying 12 kN has a coefficient of rolling resistance of 0.08 on a tilled field. What pull is needed to tow it on level ground at steady speed?

  1. 150 kN
  2. 0.48 kN
  3. 0.96 kN
  4. 11.04 kN
Answer and working

C. 0.96 kN

Pull = coefficient × load = 0.08 × 12 = 0.96 kN. Halving for two wheels is wrong: the coefficient applies to the total load carried. 150 kN divides the load by the coefficient; 0.48 kN halves it; 11.04 kN subtracts the resistance from the load.

A study plan for Mechanics of Tillage & Traction (Soil Dynamics) in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 49 questions): Traction theory: slip, rolling resistance and net traction (9, 18%); Longitudinal and lateral stability (5, 10%); Dynamic properties and strength of soil (4, 8%); Prediction of draft (4, 8%); Tractive efficiency (4, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Wheel and track mechanics (4, 8%); Determination of the centre of gravity (3, 6%); Soil compaction by vehicles (3, 6%); Soil-tool mechanics (3, 6%); Tractor chassis mechanics (3, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Weight transfer (3, 6%); Cone index and cone penetrometer (2, 4%); Traction in wetland soils (2, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Longitudinal and lateral stability (1 hard of 5), Traction theory: slip, rolling resistance and net traction (1 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Cone index and cone penetrometer (2 easy of 2); Dynamic properties and strength of soil (3 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Mechanics of Tillage & Traction (Soil Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.