LAISHA
Open Laisha

ICAR AIEEA-PG Surveying & Levelling: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
109written to this exam in this subject
12syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Surveying & Levelling in ICAR AIEEA-PG

Single-answer MCQs mixing definitions (types of bearings, contour characteristics, plane-table methods, theodolite axes, levelling terms) with quick calculations (back bearings, RLs, areas and volumes).

Measuring land, levels and volumes, from chain survey to total station and GNSS, and designing land grading.

Our 109 ICAR AIEEA-PG questions in this subject: 43 easy, 46 medium, 20 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

In a prismatic compass, the zero of the graduated ring is placed at the south end because

  1. sighting is through a prism opposite the object, so a north sight must read 0° at that end
  2. the compass reads quadrantal bearings
  3. the magnetic needle points south in the northern hemisphere, so zero must be set at the south
  4. the graduated ring rotates with the line of sight, so its zero must trail the sight vane by 180°
Answer and working

A. sighting is through a prism opposite the object, so a north sight must read 0° at that end

The ring is fixed to the needle and read through the prism at the eye end, diametrically opposite the object vane; to read 0° on a northward sight the zero must sit at the south end, and the figures are written inverted to read correctly through the prism. It reads whole-circle, not quadrantal, bearings, and its ring does not rotate with the sight (that is the surveyor's compass).

Question 2 · medium

Which method of orienting a plane table is the more accurate?

  1. Back-sighting along a previously drawn line
  2. Estimating by eye
  3. Orienting by the sun's position
  4. Using the trough compass
Answer and working

A. Back-sighting along a previously drawn line

Back-sighting relies on a line already plotted, so it is as accurate as the plotting. The trough compass is quick but subject to local attraction and needle errors, so it is used only where no back station is available.

Question 3 · easy

A point on which both a foresight and a backsight are taken in a levelling line is called a

  1. intermediate station
  2. benchmark
  3. change point
  4. station point
Answer and working

C. change point

At a change (turning) point the foresight closes one set-up and the backsight opens the next, carrying the RL forward. A benchmark has a known RL; an intermediate station has only one reading.

Question 4 · easy

Which indirect method of contouring is most suitable for a long narrow strip such as a canal alignment?

  1. Radial lines from a single station
  2. Cross-sections at intervals along the centre line
  3. Grid of squares over the whole area
  4. Direct method on every contour
Answer and working

B. Cross-sections at intervals along the centre line

For a route the ground is profiled along the centre line and cross-sectioned at regular chainages, which directly gives the data for earthwork. Grids suit compact areas; radial tacheometry suits hilly country.

Question 5 · easy

A vernier theodolite has main-scale divisions of 20 minutes and 60 vernier divisions. What is its least count?

  1. 1 minute
  2. 20 minutes
  3. 20 seconds
  4. 3 minutes
Answer and working

C. 20 seconds

Least count = value of one main-scale division / number of vernier divisions = 20′/60 = 1/3′ = 20″.

Question 6 · medium

Taking the mean of face-left and face-right observations of a horizontal angle eliminates all of the following EXCEPT

  1. line of collimation not perpendicular to the horizontal axis
  2. horizontal axis not perpendicular to the vertical axis
  3. index error of the vertical circle
  4. error due to the vertical axis not being truly vertical
Answer and working

D. error due to the vertical axis not being truly vertical

Face changes reverse the sign of collimation, trunnion-axis and index errors, so they cancel in the mean. A tilted vertical axis tilts the horizontal axis the same way on both faces, so it does not cancel; careful levelling is the only remedy.

Question 7 · medium

The transit rule for balancing a traverse is preferred over Bowditch's rule when

  1. the traverse is open
  2. a compass is used for the bearings
  3. distances are measured more precisely than angles
  4. angles are measured more precisely than distances
Answer and working

D. angles are measured more precisely than distances

The transit rule distributes corrections in proportion to the size of each latitude and departure, which assumes angles are good and lengths poorer (theodolite with tape). Bowditch assumes equal effect of angular and linear errors and is the usual rule for compass traverses. Neither can be applied to an open traverse.

Question 8 · medium

A 40 m long prismoid has end areas 12.0 and 24.0 m² and a mid-section area (computed from the mid-depth) of 17.5 m². What is its volume?

  1. 1413.3 m³
  2. 706.7 m³
  3. 720.0 m³
  4. 700.0 m³
Answer and working

B. 706.7 m³

V = (L/6)(A1 + 4Am + A2) = (40/6)(12 + 70 + 24) = 706.7 m³. Average end area gives 720.0 m³ (an overestimate for a prismoid); using L/3 doubles the answer because L here is the full length. 1413.3 m³ uses L/3; 700.0 m³ multiplies the mid-section area by the length.

Question 9 · medium

When is the plane method of land-grading design NOT the best choice?

  1. On fields so irregular that a single plane would require excessive earth movement
  2. When the field is square
  3. On nearly uniform fields
  4. When least-squares fitting can be computed quickly by software instead of by hand calculation
Answer and working

A. On fields so irregular that a single plane would require excessive earth movement

A single best-fit plane is efficient for fairly uniform fields; where the surface is strongly irregular, profile, plan-inspection or contour-adjustment methods allow varying grades and cut far less earth.

Question 10 · hard

In a two-peg test with pegs A and B 80 m apart, a level set midway reads 1.625 m on A and 1.405 m on B. Set close to A, it reads 1.540 m on A and 1.340 m on B. What is the collimation error and the direction of the line of sight?

  1. 0.020 m in 80 m, inclined upwards
  2. No error; the line of sight is horizontal
  3. 0.200 m in 80 m, inclined upwards
  4. 0.020 m in 80 m, inclined downwards
Answer and working

A. 0.020 m in 80 m, inclined upwards

From the midway set-up the errors cancel, so the true difference is 1.625 − 1.405 = 0.220 m (B higher). From near A, the correct reading on B should be 1.540 − 0.220 = 1.320 m; the observed 1.340 m is 0.020 m too high over 80 m (0.00025 m/m). A reading too high at the far staff means the line of sight rises above horizontal, i.e. inclined upwards.

A study plan for Surveying & Levelling in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (40% of the 109 questions): Chain and tape surveying, including tape corrections (12, 11%); Theodolite traversing and closing error (12, 11%); Compass traversing and bearings (10, 9%); Levelling: rise-and-fall and height-of-instrument methods (10, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Contouring (9, 8%); Plane table surveying (9, 8%); Reciprocal levelling (9, 8%); Computation of area: trapezoidal and Simpson's rules (8, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Earthwork volume computation (8, 7%); GPS/GNSS surveying (8, 7%); Land grading and levelling design (7, 6%); Total station (7, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Compass traversing and bearings (4 hard of 10), Levelling: rise-and-fall and height-of-instrument methods (3 hard of 10), Earthwork volume computation (2 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Land grading and levelling design (4 easy of 7); Contouring (4 easy of 9).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Surveying & Levelling

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.