LAISHA
Open Laisha

ICAR AICE-JRF/SRF Workshop Technology & Manufacturing: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
33written to this exam in this subject
12syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Workshop Technology & Manufacturing in ICAR AICE-JRF/SRF

Manufacturing processes for farm machine parts at postgraduate depth: heat treatment and hardenability of tillage steels, welding processes and weldability (carbon equivalent, hydrogen cracking), casting design (gating, risering, Chvorinov), press working forces, machining parameters and tool life, jigs and fixtures, and limits and fits.

How farm machines are made: joining, casting, machining, heat treatment and measurement, up to building a prototype.

Our 33 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 8 medium, 24 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

A weld is made at 25 V and 200 A with a travel speed of 5 mm/s. Taking an arc efficiency of 0.8, what is the heat input per unit length?

  1. 800 J/mm
  2. 1000 J/mm
  3. 4000 J/mm
  4. 0.8 J/mm
Answer and working

A. 800 J/mm

Heat input = ηVI/v = 0.8 × 25 × 200 / 5 = 800 J/mm (0.8 kJ/mm). 1000 J/mm ignores efficiency; 4000 J/mm is the arc power ηVI in J/s, not divided by travel speed; 0.8 J/mm is a units slip.

Question 2 · hard

In orthogonal cutting with a rake angle of 10°, the uncut chip thickness is 0.5 mm and the chip thickness is 1.25 mm. What is the shear angle?

  1. 21.8°
  2. 67.1°
  3. 22.9°
  4. 32.9°
Answer and working

C. 22.9°

r = 0.5/1.25 = 0.4; tan φ = r cos α/(1 − r sin α) = 0.394/0.931 = 0.423, φ = 22.9°. 21.8° is tan⁻¹ r, ignoring rake; 67.1° is the complement; 32.9° adds the rake angle to the correct answer.

Question 3 · hard

Why does down (climb) milling require a backlash eliminator on the table feed screw?

  1. The cutter lifts the work off the table and the screw must hold it down against the cut
  2. The cutter pulls the work in the direction of feed and drags the table forward through any backlash
  3. Down milling runs at double the spindle speed, so the screw would otherwise overheat
  4. The chip starts thin, so the cutter rubs and the feed screw slips under the friction
Answer and working

B. The cutter pulls the work in the direction of feed and drags the table forward through any backlash

In climb milling the cutting force has a component in the feed direction, so any slack between screw and nut lets the cutter snatch the table forward, causing chatter or a broken cutter. Lifting the work and a thin starting chip describe up (conventional) milling.

Question 4 · hard

When grinding a hardened tool steel, why is a softer-grade wheel normally preferred?

  1. A soft wheel runs safely at higher surface speed than a hard-grade wheel
  2. Blunted grains break out readily, exposing sharp new grains instead of glazing
  3. Softer bonds hold the grains longer, so the wheel wears much more slowly
  4. Hard steel loads the wheel pores, and only soft wheels can be dressed later
Answer and working

B. Blunted grains break out readily, exposing sharp new grains instead of glazing

Hard work blunts grains quickly; a softer bond releases them so the wheel self-sharpens and does not glaze and burn the work. Grade does not raise permissible speed, a soft bond holds grains less firmly (faster wear), and any vitrified wheel can be dressed.

Question 5 · hard

A 50.0 mm diameter blank is to be produced by blanking, with a clearance of 0.1 mm per side. What are the die and punch diameters?

  1. Die 50.2 mm, punch 50.0 mm
  2. Die 50.1 mm, punch 49.9 mm
  3. Die 50.0 mm, punch 49.8 mm
  4. Die 50.0 mm, punch 49.9 mm
Answer and working

C. Die 50.0 mm, punch 49.8 mm

In blanking the blank takes the size of the die opening, so the die is 50.0 mm and the punch is smaller by twice the per-side clearance: 49.8 mm. Die 50.2 / punch 50.0 is the piercing rule (punch = hole). Splitting the clearance gives the wrong blank size; 49.9 uses the clearance only once.

Question 6 · hard

A fixture designer adds a fourth fixed rest under the primary face of a sawn steel plate that already sits on three rests. What is the likely result?

  1. The plate is located more accurately, because more rests mean less error
  2. The plate cannot be clamped at all, because four rests block the clamps
  3. The plate's sixth degree of freedom is now removed without a third face
  4. The plate rocks or is bent by clamping, because the face is over-constrained
Answer and working

D. The plate rocks or is bent by clamping, because the face is over-constrained

Three points define a plane; a fourth fixed point on an imperfect surface means the work touches only three at a time and rocks, or is distorted when clamped. If more support is needed, an adjustable or spring-loaded rest is used. Extra rests on one face do not locate other directions.

Question 7 · hard

A 0.40% carbon steel is cooled slowly to just below 727 °C. Taking the eutectoid at 0.76% C and the carbon content of ferrite as 0.022%, what mass fraction of the structure is pearlite?

  1. About 53%
  2. About 49%
  3. About 40%
  4. About 51%
Answer and working

D. About 51%

Lever rule: W_pearlite = (0.40 − 0.022)/(0.76 − 0.022) = 0.378/0.738 = 0.512. 53% ignores carbon in ferrite (0.40/0.76); 49% is the proeutectoid ferrite fraction; 40% simply takes the carbon percentage.

Question 8 · easy

Which test is used to measure and compare the hardenability of steels for tillage tools?

  1. Charpy V-notch impact test
  2. Jominy end-quench test
  3. Erichsen cupping test
  4. Brinell hardness test alone
Answer and working

B. Jominy end-quench test

In the Jominy test a standard bar is austenitised, water-sprayed on one end, and hardness is measured along its length, showing how deep martensite forms. Charpy measures toughness, Erichsen measures sheet formability, and a single Brinell value gives hardness at one point, not depth.

Question 9 · hard

Using the ISO standard tolerance unit i = 0.45∛D + 0.001D (µm) and IT7 = 16i, what is the IT7 tolerance for the 30–50 mm diameter step?

  1. About 39 µm
  2. About 16 µm
  3. About 25 µm
  4. About 1.6 µm
Answer and working

C. About 25 µm

D = √(30 × 50) = 38.73 mm; i = 0.45 × 3.383 + 0.0387 = 1.561 µm; IT7 = 16 × 1.561 = 25.0 µm. 39 µm is IT8 (25i); 16 µm forgets to multiply by i; 1.6 µm is i itself.

Question 10 · hard

A steel hub with a 50 mm bore is to be shrunk onto a shaft with 0.05 mm interference. Taking α = 12 × 10⁻⁶ /°C, what minimum temperature rise just removes the interference?

  1. About 42 °C
  2. About 833 °C
  3. About 83 °C
  4. About 167 °C
Answer and working

C. About 83 °C

ΔT = δ/(αD) = 0.05/(12 × 10⁻⁶ × 50) = 83 °C. 42 °C uses 100 mm, double the bore; 833 °C is a decimal slip that would also spoil the heat treatment; 167 °C uses the radius in the denominator. In practice a little more is added for assembly clearance.

A study plan for Workshop Technology & Manufacturing in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 33 questions): MIG and TIG welding and testing of welded joints (5, 15%); Heat treatment of steels (4, 12%); Jigs, fixtures and gauges (4, 12%); Press working of sheet metal (4, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Casting processes (3, 9%); Drilling, milling and shaping (3, 9%); Lathe operations (3, 9%); Metrology and measurement in the workshop (3, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Arc and gas welding (1, 3%); Fitting, carpentry and smithy (1, 3%); Prototype fabrication (1, 3%); Specification of engineering materials (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: MIG and TIG welding and testing of welded joints (5 hard of 5), Drilling, milling and shaping (3 hard of 3), Lathe operations (3 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Heat treatment of steels (1 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Workshop Technology & Manufacturing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.