ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
PG-level depth: Heisler charts and product solutions, fin effectiveness, radiation networks and shields, ε–NTU relations and regeneration efficiency in pasteurisers, condensation and boiling regimes in evaporators, the heat–mass analogy and Lewis relation, Fick's second law and effective diffusivity, and thin-layer drying models.
Conduction, convection, radiation, heat exchangers and diffusion — the physics of drying, cooling, freezing and cold-store walls.
Our 71 ICAR AICE-JRF/SRF questions in this subject: 3 easy, 41 medium, 27 hard, across 12 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
In laminar flow of a heavy oil (Pr = 1,000) along a heated flat plate, with heating starting at the leading edge, the thermal boundary-layer thickness is approximately
B. one-tenth of the velocity boundary-layer thickness
For laminar flat-plate flow δ/δ_t ≈ Pr^(1/3). With Pr = 1,000, Pr^(1/3) = 10, so δ_t ≈ δ/10. High-Pr fluids diffuse momentum much faster than heat. Ten times thicker would apply to a very low-Pr fluid such as a liquid metal; one-thousandth wrongly uses Pr to the first power.
A spherical thermocouple junction 1 mm in diameter (ρ = 8,500 kg/m³, c = 400 J/kg·K) is placed in a gas stream with h = 200 W/m²·K. Treating it as a lump, its time constant is closest to
A. 2.83 s
τ = ρVc/(hA_s) = ρc(D/6)/h, because V/A_s = D/6 for a sphere. τ = 8500 × 400 × (0.001/6)/200 = 2.83 s. Using V/A_s = r gives 8.5 s; using D gives 17 s; 0.047 s results from a spurious division by 60.
In a counterflow exchanger the two fluids have equal heat-capacity rates. The hot fluid enters at 80 °C and the cold fluid enters at 20 °C and leaves at 60 °C. The mean temperature difference to use in Q = UAΔT_m is
A. 20 °C
Equal C means the hot fluid falls by the same 40 °C, leaving at 40 °C. ΔT1 = 80 − 60 = 20 °C and ΔT2 = 40 − 20 = 20 °C: the difference is constant along the exchanger, so ΔT_m = 20 °C. The LMTD formula gives 0/0 but its limit is 20 °C. 40 °C is the hot fluid's temperature drop, not the driving difference.
An electrically heated element submerged in water is controlled by its power input. If the power is raised just above the critical heat flux, the element
C. jumps to the film-boiling branch at a much higher surface temperature, risking burnout
With heat flux imposed, the operating point cannot follow the falling transition branch; it jumps at the same flux to the film-boiling curve, where the surface temperature can be hundreds of degrees higher and may exceed the element's melting point. Transition boiling can be followed only when surface temperature is controlled, not heat flux.
For laminar film condensation on a vertical plate, Nusselt's analysis gives h ∝ L^(−1/4). If the plate height is doubled with all else the same, the average coefficient becomes
D. 0.841 times the original
h ∝ L^(−1/4), so h_new/h_old = 2^(−0.25) = 0.841. The thicker film on the lower part of a taller plate lowers the average coefficient, but only weakly; the total heat flow still rises, because the area doubles (1.68 times).
The typical order of magnitude of binary diffusion coefficients at ordinary temperature is
A. gases about 10⁻⁵ m²/s, liquids about 10⁻⁹ m²/s, solids much smaller
Gas-phase diffusivities are around 10⁻⁵ m²/s (water vapour in air about 2.5 × 10⁻⁵), liquid-phase around 10⁻⁹ m²/s, and diffusion in solids and food matrices is slower still. This four-orders-of-magnitude gap is why internal diffusion controls drying in the falling-rate period.
A solute diffuses steadily through a stagnant liquid layer 2 mm thick with D = 2 × 10⁻⁹ m²/s. Its concentrations on the two faces differ by 0.5 kmol/m³. The molar flux is
B. 5.00 × 10⁻⁷ kmol/m²·s
N = DΔC/L = 2 × 10⁻⁹ × 0.5/0.002 = 5.0 × 10⁻⁷ kmol/m²·s, the mass analogue of Q = kAΔT/L. Entering L as 2 (mm) gives 5 × 10⁻¹⁰; multiplying by L gives 2 × 10⁻¹²; omitting ΔC gives 1 × 10⁻⁶ with the wrong units.
Over a moist product in a dryer the convective heat-transfer coefficient is 30 W/m²·K. Air has ρ = 1.2 kg/m³ and c_p = 1,007 J/kg·K, and Le = 0.88. By the Chilton–Colburn analogy, h/h_m = ρ c_p Le^(2/3), the mass-transfer coefficient is closest to
D. 27.0 × 10⁻³ m/s
h_m = h/(ρ c_p Le^(2/3)) = 30/(1.2 × 1007 × 0.88^(2/3)) = 30/(1.2 × 1007 × 0.9183) = 0.02703 m/s. Taking Le^(2/3) = 1 (the Lewis relation) gives 24.8 × 10⁻³, a small error for air–water; using c_p in kJ/kg·K gives an impossible 27.0 m/s; using Le^(1/3) gives 25.9 × 10⁻³.
Thin-layer drying of a grain sample follows the Lewis (Newton) model MR = exp(−kt) with k = 0.2 h⁻¹. The time to reach MR = 0.1 is closest to
D. 11.5 h
t = −ln(MR)/k = ln(10)/0.2 = 11.5 h. Using a linear decline gives 4.5 h; using log₁₀ instead of the natural logarithm gives 5.0 h; 0.5 h is MR/k.
The Chilton–Colburn analogy states that j_H = St·Pr^(2/3) and j_D = St_m·Sc^(2/3) are both equal to
B. C_f/2, half the skin-friction coefficient
The j-factor analogy links heat, mass and momentum transfer: j_H = j_D = C_f/2 for flows without form drag, valid roughly for 0.6 < Pr < 60 and 0.6 < Sc < 3,000. It lets a measured friction factor or heat-transfer coefficient give the mass-transfer coefficient.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.