LAISHA
Open Laisha

ICAR AICE-JRF/SRF Agricultural Drainage Engineering: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
59written to this exam in this subject
11syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Agricultural Drainage Engineering in ICAR AICE-JRF/SRF

PG-depth theory: assumptions of Hooghoudt, Ernst, Kirkham and Glover-Dumm, equivalent depth, drainable porosity, envelope design criteria, USBR dynamic equilibrium, bio-drainage and vertical drainage, reclamation chemistry and the gypsum requirement.

Removing excess water and salt: surface and subsurface drain design, and reclaiming saline and sodic land.

Our 59 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 36 medium, 22 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

In a piezometer nest, the piezometer open at 2 m depth has its water level 0.8 m below the ground surface and the one open at 6 m depth has its water level 0.3 m below the surface. What is the direction and magnitude of the vertical hydraulic gradient between them?

  1. Upward, gradient 0.125
  2. Downward, gradient 0.125
  3. Upward, gradient 0.5
  4. Downward, gradient 0.083
Answer and working

A. Upward, gradient 0.125

Taking the ground surface as datum, head at 2 m = -0.8 m and at 6 m = -0.3 m. The deeper point has the higher head, so water moves upward. Gradient = 0.5 m / (6 - 2) m = 0.125. Reporting 0.5 forgets to divide by the 4 m distance; 'downward' reads the levels as depths instead of heads. Upward seepage means relief wells or drains designed for extra inflow.

Question 2 · medium

Over six consecutive days the water-table depths were 5, 15, 25, 35, 20 and 40 cm. What is SEW30 for this period?

  1. 40 cm-days
  2. 65 cm-days
  3. 55 cm-days
  4. 4 cm-days
Answer and working

C. 55 cm-days

SEW30 sums (30 - depth) only for days when the water table is shallower than 30 cm: 25 + 15 + 5 + 10 = 55 cm-days; the 35 and 40 cm days add nothing. 40 wrongly subtracts the deep days; 65 adds depths instead of excesses; 4 counts days.

Question 3 · hard

In Hiler's stress day index (SDI) for drainage design, what are the two factors multiplied for each growth stage?

  1. A stress-day factor such as SEW30 and a crop susceptibility factor for that stage
  2. The drainage coefficient and the drain spacing chosen for that growth stage
  3. Drainable porosity and saturated hydraulic conductivity of the soil at each stage
  4. Rainfall return period and runoff coefficient
Answer and working

A. A stress-day factor such as SEW30 and a crop susceptibility factor for that stage

SDI = sum of (SD x CS): the stress-day factor measures how wet the soil was, and the crop susceptibility factor measures how sensitive the crop is at that stage. The other pairs are design inputs, not stress indices.

Question 4 · hard

Ernst: q = 6 mm/day, L = 40 m, Kv = 0.5 m/day over Dv = 0.3 m above drains, transmissivity Sum(KD) = 4.0 m2/day, radial layer Kr = 0.8 m/day and Dr = 5 m, wetted perimeter u = 0.3 m, a = 1. What total midpoint head h results?

  1. 0.30 m
  2. 0.42 m
  3. 0.27 m
  4. 0.57 m
Answer and working

D. 0.57 m

hv = qDv/Kv = 0.006 x 0.3 / 0.5 = 0.0036 m. hh = qL^2 / (8 Sum KD) = 0.006 x 1600 / 32 = 0.300 m. hr = (qL / pi Kr) ln(Dr/u) = (0.24 / 2.513) x ln(16.67) = 0.269 m. Total = 0.57 m. 0.30 m keeps only the horizontal term; 0.42 m uses log10 in the radial term; 0.27 m is the radial term alone.

Question 5 · hard

Glover-Dumm: K = 1.0 m/day, average flow depth D = 4.5 m, drainable porosity 0.05, initial midpoint head 1.0 m above drains, required head 0.7 m after 3 days (initial shape a fourth-degree parabola). What drain spacing is needed?

  1. 23 m
  2. 67 m
  3. 73 m
  4. 7.3 m
Answer and working

C. 73 m

L^2 = pi^2 K D t / [mu ln(1.16 h0/ht)] = 9.870 x 1.0 x 4.5 x 3 / [0.05 x ln(1.657)] = 133.2 / (0.05 x 0.5051) = 5276 m2; L = 73 m. 23 m omits pi^2; 67 m uses 1.27 (flat initial water table); 7.3 m enters porosity as 5 instead of 0.05.

Question 6 · hard

In the Glover-Dumm spacing equation, with all else unchanged, the drainable porosity of a soil is found to be twice the design value. The required spacing becomes:

  1. Twice the original spacing
  2. Half the original spacing
  3. The original spacing divided by about 1.41
  4. The original spacing multiplied by about 1.41
Answer and working

C. The original spacing divided by about 1.41

L^2 is inversely proportional to mu, so L scales with 1/sqrt(mu): doubling mu divides L by sqrt 2 = 1.41. More water must drain per metre of fall, so drains must be closer, not wider.

Question 7 · medium

Mole drainage is best suited to which situation?

  1. A stable clay subsoil in which an unlined channel keeps its shape
  2. A loose sandy subsoil
  3. A stony soil with boulders
  4. A deep peat that stays soft and is subject to subsidence after drainage
Answer and working

A. A stable clay subsoil in which an unlined channel keeps its shape

A mole plough forms an unlined channel that survives only in cohesive, stable clay. It collapses in sand, cannot be drawn through stones, and deforms in peat.

Question 8 · medium

Vertical drainage by tubewells is most attractive where:

  1. A thin clay layer lies over an impermeable rock
  2. Groundwater is highly saline and there is no outlet or evaporation pond for disposing of it
  3. The soil is a heavy clay with a perched water table that tubewells can drain quickly
  4. A transmissive aquifer lies beneath and the pumped water is fresh enough to reuse
Answer and working

D. A transmissive aquifer lies beneath and the pumped water is fresh enough to reuse

The pumped water then becomes an irrigation supply, giving conjunctive use. Thin clay over rock and perched tables have no aquifer to pump; saline water without an outlet creates a disposal problem.

Question 9 · medium

Controlled drainage (drainage water management) with an adjustable outlet structure is used mainly to:

  1. Increase the drainage coefficient during storms by lowering the outlet well below the normal drain depth
  2. Pump saline water into evaporation ponds
  3. Prevent ochre formation
  4. Raise the drain water level when drainage is not needed, conserving water and cutting nitrate losses
Answer and working

D. Raise the drain water level when drainage is not needed, conserving water and cutting nitrate losses

Raising the outlet holds water in the profile outside critical periods and cuts nitrate export; it is lowered before field operations.

Question 10 · medium

Using the leaching relation (C/C0)(Dw/Ds) = 0.3 for continuous ponding, how much water must infiltrate to reduce salinity in the top 0.6 m to 20 % of its initial value?

  1. 0.3 m
  2. 0.036 m
  3. 0.9 m
  4. 3.0 m
Answer and working

C. 0.9 m

Dw = k x Ds / (C/C0) = 0.3 x 0.6 / 0.2 = 0.9 m. 0.3 m uses k = 0.1, which applies to intermittent ponding; 0.036 m multiplies by C/C0; 3.0 m omits k. Constants are soil-specific; confirm in a trial.

A study plan for Agricultural Drainage Engineering in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (51% of the 59 questions): Kirkham and Glover-Dumm equations (9, 15%); Drain pipes and envelopes (7, 12%); Subsurface drain spacing: Hooghoudt and Ernst (7, 12%); Vertical drainage and bio-drainage (7, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Reclamation of saline and sodic soils and gypsum requirement (6, 10%); Drainage coefficient (5, 8%); Interceptor and relief drains (5, 8%); Salinity and the leaching requirement (5, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Irrigation water quality: EC, SAR and RSC (4, 7%); Causes and effects of waterlogging (2, 3%); Surface drainage design (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Subsurface drain spacing: Hooghoudt and Ernst (4 hard of 7), Irrigation water quality: EC, SAR and RSC (2 hard of 4), Causes and effects of waterlogging (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Subsurface drain spacing: Hooghoudt and Ernst (1 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Agricultural Drainage Engineering

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.