LAISHA
Open Laisha

ICAR AICE-JRF/SRF Storage Engineering, Material Handling & Packaging: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
69written to this exam in this subject
11syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Storage Engineering, Material Handling & Packaging in ICAR AICE-JRF/SRF

Unit 6 (material handling, packaging and transport) and Unit 7 (storage engineering) at PG depth: derivation and assumptions of Janssen's equation, Airy's wedge analysis, flow patterns and Jenike design, moisture migration, airflow resistance and fan selection, fumigation CT and resistance, CA/MA equilibrium, permeation theory, shelf-life models and packaging machinery.

Storing grain and produce safely, the loads it puts on bins and silos, and the conveyors and packages that move and protect it.

Our 69 ICAR AICE-JRF/SRF questions in this subject: 2 easy, 40 medium, 27 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

Why is headspace carbon dioxide monitoring used as an early warning of spoilage in stored grain?

  1. CO2 is released only when grain germinates, so it signals sprouting before any mould can develop
  2. CO2 concentration falls as mould grows
  3. CO2 is a by-product of phosphine decomposition, so it signals fumigant breakdown and reinfestation
  4. Insects and moulds respire and raise CO2 before a temperature rise reaches a distant sensor cable
Answer and working

D. Insects and moulds respire and raise CO2 before a temperature rise reaches a distant sensor cable

Because grain conducts heat poorly, a hot spot may be far from any temperature cable and go unnoticed; the CO2 it produces diffuses and is carried by air movement to the headspace, where it can be sensed earlier. CO2 rises, not falls, with biological activity, and it is not produced by phosphine.

Question 2 · hard

In a 6 m diameter bin (μ′ = 0.4, k = 0.4), at roughly what depth does the Janssen pressure reach 95% of its limiting value?

  1. 9.4 m
  2. 56.2 m
  3. 28.1 m
  4. 11.2 m
Answer and working

C. 28.1 m

1 − e^−x = 0.95 when x = 3 (e^−3 = 0.050). So μ′kh/R = 3 → h = 3R/(μ′k) = 3 × 1.5/(0.4 × 0.4) = 28.1 m. At h = R/(μ′k) = 9.4 m the pressure is only 63% of the limit; using the bin radius (3 m) instead of the hydraulic radius R = D/4 = 1.5 m gives 56.2 m. 11.2 m omits k (3 × 1.5/0.4).

Question 3 · hard

A square bin of 5 m side holds grain of specific weight 7.6 kN/m³. With k = 0.45 and μ′ = 0.35, what is the Janssen vertical pressure at 12 m depth?

  1. 91.2 kPa
  2. 64.0 kPa
  3. 21.2 kPa
  4. 47.0 kPa
Answer and working

D. 47.0 kPa

R for a square = side/4 = 1.25 m. μ′kh/R = 0.35 × 0.45 × 12/1.25 = 1.5120. V = (γR/μ′k)(1 − e^−x) = (60.317)(1 − 0.2205) = 47.0 kPa. γh = 91.2 kPa ignores wall friction; using R = side/2 gives 64.0 kPa; kV = 21.2 kPa is the lateral pressure.

Question 4 · medium

Why do grain-bin design standards apply overpressure factors to static Janssen pressures?

  1. Janssen always overestimates pressure, so the overpressure factors are applied to reduce the design wall load
  2. Pressures during discharge, eccentric flow and thermal or moisture effects can exceed static fill pressures
  3. To account only for roof loads, which can bear on the wall
  4. Because grain is lighter than water, so static Janssen pressures must be scaled up to a fluid equivalent
Answer and working

B. Pressures during discharge, eccentric flow and thermal or moisture effects can exceed static fill pressures

Measured wall pressures during emptying (and with eccentric flow, swelling or wall contraction in cold weather) can exceed the static Janssen values, so standards multiply them by factors. The factors increase, not reduce, design loads.

Question 5 · medium

A 3 g tablet contains 56% aluminium phosphide (AlP, 57.95 g/mol). How much phosphine (PH3, 34.00 g/mol) can it release?

  1. 1.68 g
  2. 1.76 g
  3. 0.99 g
  4. 2.86 g
Answer and working

C. 0.99 g

AlP = 3 × 0.56 = 1.68 g = 0.0290 mol; 1 mol AlP gives 1 mol PH3, so PH3 = 0.0290 × 34.00 = 0.99 g (about 1 g). 1.68 g is the mass of AlP, not PH3; 1.76 g ignores the 56% content; inverting the molar mass ratio gives 2.86 g.

Question 6 · medium

A fumigation label concentration is given as 1 g/m³ of phosphine. What is this in ppm (v/v) at 25 °C?

  1. 659 ppm
  2. 719 ppm
  3. 1,000 ppm
  4. 1,391 ppm
Answer and working

B. 719 ppm

ppm = (mg/m³) × Vm/M = 1000 × 24.45/34.0 = 719 ppm. Using 22.41 L/mol gives 659; treating mg/m³ as ppm gives 1,000; inverting gives 1,391.

Question 7 · easy

A condition common to CA, MA and hermetic storage is that

  1. It must be gas-tight
  2. Oxygen must be above 21%
  3. Temperature must be above 30 °C
  4. The product must be fumigated first
Answer and working

A. It must be gas-tight

Without a seal, air leaks in and the modified atmosphere reverts to air. None requires raised O2, high temperature or prior fumigation.

Question 8 · medium

How does a multihead combination weigher achieve accurate fills of irregular pieces such as snacks?

  1. It measures a fixed volume with a cup
  2. It counts pieces optically with a camera and stops the fill when the target number is reached
  3. A computer selects the combination of weigh buckets whose total is closest to the target
  4. It fills by a set number of auger turns
Answer and working

C. A computer selects the combination of weigh buckets whose total is closest to the target

Each head weighs a partial charge; the controller evaluates combinations and discharges the best one, giving high accuracy for irregular products. Cup and auger fillers are volumetric.

Question 9 · medium

How does inclining a screw conveyor affect its capacity at constant speed?

  1. Capacity increases because gravity helps
  2. Capacity is unaffected
  3. Capacity doubles at 45°
  4. Capacity falls
Answer and working

D. Capacity falls

As the angle increases, material falls back over the flight and the loading efficiency drops, so capacity falls.

Question 10 · medium

En-masse (chain) conveyors move grain

  1. By blowing air through a pipe
  2. By throwing grain forward with a high-speed belt, as in a centrifugal grain thrower
  3. As a continuous mass in an enclosed casing, gently and at moderate capacity
  4. On an open inclined vibrating tray
Answer and working

C. As a continuous mass in an enclosed casing, gently and at moderate capacity

In an en-masse conveyor, flights on a chain drag the material, which moves as a solid mass in the casing, with little damage. The other options describe pneumatic, thrower and vibratory systems.

A study plan for Storage Engineering, Material Handling & Packaging in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 69 questions): Janssen's and Airy's theories of bin pressure (9, 13%); Aeration of stored grain (8, 12%); Barrier properties of packages (8, 12%); Controlled and modified atmosphere storage (8, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Fumigation (8, 12%); Causes of storage losses (6, 9%); Packaging materials: paper, plastics and laminates (6, 9%); Bins and silos (5, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Design of conveyors and elevators (5, 7%); Packaging machines (5, 7%); Bag and bulk storage (1, 1%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Janssen's and Airy's theories of bin pressure (6 hard of 9), Aeration of stored grain (5 hard of 8), Barrier properties of packages (5 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Packaging machines (1 easy of 5); Controlled and modified atmosphere storage (1 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Storage Engineering, Material Handling & Packaging

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.