LAISHA
Open Laisha

GATE Storage Engineering, Material Handling & Packaging: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
60written to this exam in this subject
11syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Storage Engineering, Material Handling & Packaging in GATE

Section 6 (Storage Systems; Size Reduction and Material Handling; packaging material and machines). Bin and silo pressure has appeared in most recent papers: Janssen vertical and lateral pressure at a given depth, the limiting pressure, Rankine's k from the angle of internal friction, and the shallow-or-deep test. Also silo capacity from bulk density, bucket-elevator head-pulley speed, screw and belt conveyor capacity, and permeation or WVTR through a package film, often as numerical-answer questions with two or three linked steps.

Storing grain and produce safely, the loads it puts on bins and silos, and the conveyors and packages that move and protect it.

Our 60 GATE questions in this subject: 21 easy, 20 medium, 19 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · easy

Aflatoxin contamination of stored maize and groundnut is produced chiefly by

  1. Fusarium graminearum and other field-infecting Fusarium species
  2. Penicillium roqueforti, the blue-cheese mould of cool damp stores
  3. Sitophilus zeamais
  4. Aspergillus flavus and related Aspergillus species
Answer and working

D. Aspergillus flavus and related Aspergillus species

Aflatoxins are produced by Aspergillus flavus and A. parasiticus. Fusarium graminearum produces deoxynivalenol and zearalenone; Sitophilus zeamais is the maize weevil, an insect, not a toxin producer.

Question 2 · hard

A cylindrical bin of 6 m diameter is filled with wheat (bulk density 780 kg/m³) to an eave height of 10 m and heaped at its angle of repose of 25°. What mass does it hold?

  1. 220.5 t
  2. 230.8 t
  3. 251.4 t
  4. 882.2 t
Answer and working

B. 230.8 t

Cylinder: πD²H/4 = π × 6² × 10/4 = 282.74 m³. Cone height = (D/2)tan25° = 1.399 m; cone volume = πD²h/12 = 13.18 m³. Total 295.93 m³ × 780 = 230.8 t. Ignoring the cone gives 220.5 t; using πD²h/4 for the cone (a cylinder, not a cone) gives 251.4 t; using D² without /4 gives 882.2 t.

Question 3 · medium

What is the hydraulic radius of a rectangular bin 4 m × 6 m in plan?

  1. 2.4 m
  2. 1.0 m
  3. 1.2 m
  4. 0.83 m
Answer and working

C. 1.2 m

R = A/perimeter = (4 × 6)/(2 × (4 + 6)) = 24/20 = 1.2 m. Forgetting the factor 2 in the perimeter gives 2.4 m; a/4 = 1.0 m applies only to a square; 0.83 m inverts the ratio (20/24).

Question 4 · hard

What is the maximum (limiting) lateral pressure that wheat of bulk density 780 kg/m³ can exert on the wall of a very deep 8 m diameter bin with a wall friction coefficient of 0.45?

  1. 34.0 kPa
  2. 3.47 kPa
  3. 68.0 kPa
  4. 6.89 kPa
Answer and working

A. 34.0 kPa

L_max = γR/μ′ with γ = 780 × 9.81 = 7.652 kN/m³ and R = D/4 = 2.0 m: 7.652 × 2.0/0.45 = 34.0 kPa. It does not depend on k. Using kg/m³ instead of weight density gives 3.47; using the radius D/2 instead of the hydraulic radius gives 68.0; multiplying by μ′ (6.89) is an algebra slip.

Question 5 · medium

An aeration fan delivers 50 m³/min into a flat-bottom bin of 8 m diameter with a full perforated floor. What is the superficial air velocity through the grain?

  1. 1.989 m/min
  2. 0.995 m/min
  3. 3.979 m/min
  4. 16.6 m/min
Answer and working

B. 0.995 m/min

Superficial velocity = Q/A = 50/(π × 8²/4) = 50/50.27 = 0.995 m/min (0.0166 m/s). Dividing by the circumference gives 1.989; putting the 4 m radius into πD²/4 (area 12.57 m²) gives 3.979; the last value mixes mm/s and m/min. This velocity is used with airflow-resistance data (Shedd's curves) to find pressure drop per metre.

Question 6 · medium

What is the humidity ratio of air at 25 °C and 70% RH at a pressure of 101.325 kPa?

  1. 0.0201 kg/kg dry air
  2. 0.0224 kg/kg dry air
  3. 0.4354 kg/kg dry air
  4. 0.0139 kg/kg dry air
Answer and working

D. 0.0139 kg/kg dry air

p_sat(25 °C) ≈ 3.168 kPa; p_v = 0.7 × 3.168 = 2.217 kPa. W = 0.622 p_v/(P − p_v) = 0.622 × 2.217/(101.325 − 2.217) = 0.0139. Using p_sat gives the saturated value 0.0201; omitting 0.622 gives 0.0224; 0.622 × RH is dimensionally meaningless.

Question 7 · hard

A 1 kg pack of produce respires 10 mL O2 kg⁻¹ h⁻¹ at storage temperature. The film has an oxygen transmission rate of 5000 cm³ m⁻² day⁻¹ atm⁻¹. What film area gives a steady-state internal O2 of 5% (outside 21%, total pressure 1 atm)?

  1. 0.048 m²
  2. 0.0125 m²
  3. 0.229 m²
  4. 0.300 m²
Answer and working

D. 0.300 m²

O2 consumed = 10 × 1 × 24 = 240 mL/day. At steady state this equals OTR × A × ΔpO2 = 5000 × A × (0.21 − 0.05) = 800A. A = 240/800 = 0.300 m². Ignoring the partial-pressure difference gives 0.048; using the hourly rate with a daily OTR gives 0.0125; using 0.21 as the driving force (0.229) assumes zero O2 inside.

Question 8 · medium

Which is the most likely structure for a retortable pouch?

  1. LDPE / paper / LDPE
  2. Paperboard / PE / aluminium / PE
  3. BOPP / LDPE
  4. PET / aluminium foil / cast polypropylene
Answer and working

D. PET / aluminium foil / cast polypropylene

The retort pouch needs a strong printable outer layer (PET), a total barrier (foil) and a sealant that survives retort temperatures (cast PP, higher melting than PE). Paperboard/PE/Al/PE is the aseptic carton; PE-sealed structures do not survive retorting.

Question 9 · medium

Why is cast polypropylene rather than LDPE used as the sealant in a retort pouch?

  1. PP is a better oxygen barrier than the aluminium foil, so the foil layer can be made thinner
  2. LDPE cannot be heat-sealed
  3. PP is cheaper than all other polymers
  4. PP has a higher melting point and withstands retort temperatures around and above 120 °C
Answer and working

D. PP has a higher melting point and withstands retort temperatures around and above 120 °C

LDPE softens well below retort temperatures, while PP's higher melting point keeps seals intact. Foil, not PP, provides the barrier; LDPE is an excellent sealant at ordinary temperatures.

Question 10 · hard

A horizontal screw conveyor has a 200 mm flight, a 50 mm shaft, 200 mm pitch and runs at 120 rpm with a loading efficiency of 0.4. It conveys wheat of bulk density 750 kg/m³. Capacity?

  1. 12.72 t/h
  2. 13.57 t/h
  3. 31.81 t/h
  4. 763.4 t/h
Answer and working

A. 12.72 t/h

Swept volume per revolution = (π/4)(D² − d²)p = (π/4)(0.2² − 0.05²)(0.2) = 0.005890 m³. × 120 rpm × 0.4 = 0.28274 m³/min. Mass = 0.28274 × 750 × 60 = 12,723 kg/h = 12.72 t/h. Ignoring the shaft gives 13.57; ignoring loading efficiency gives 31.81; treating rpm as rev/s gives 763.4.

A study plan for Storage Engineering, Material Handling & Packaging in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (62% of the 60 questions): Janssen's and Airy's theories of bin pressure (17, 28%); Barrier properties of packages (7, 12%); Design of conveyors and elevators (7, 12%); Aeration of stored grain (6, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Packaging materials: paper, plastics and laminates (6, 10%); Bins and silos (3, 5%); Causes of storage losses (3, 5%); Controlled and modified atmosphere storage (3, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Fumigation (3, 5%); Packaging machines (3, 5%); Warehouse management (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Bins and silos (2 hard of 3), Warehouse management (1 hard of 2), Janssen's and Airy's theories of bin pressure (8 hard of 17).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Packaging machines (2 easy of 3); Packaging materials: paper, plastics and laminates (3 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Storage Engineering, Material Handling & Packaging

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.