LAISHA
Open Laisha

GATE Post-Harvest Engineering of Cereals, Pulses & Oilseeds: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
55written to this exam in this subject
13syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Post-Harvest Engineering of Cereals, Pulses & Oilseeds in GATE

Section 6 carries roughly 14 marks a year and is mostly numerical: humidity ratio, humid volume and adiabatic mixing of air streams (asked in most recent papers); rice milling, husking coefficients and parboiling effects (most papers); wet/dry-basis conversion and water to add or remove; drying time and EMC; separation and screen effectiveness; Rittinger, Kick and Bond energy; ball-mill critical speed; bucket elevator speed. Expect two-mark questions that chain three or more steps, and conceptual one-mark items on parboiling and drying mechanisms.

Moisture, drying, parboiling, milling, cleaning, size reduction and conveying of grains, pulses and oilseeds.

Our 55 GATE questions in this subject: 15 easy, 21 medium, 19 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

How much water must be added to 500 kg of wheat at 11% wet-basis moisture to temper it to 16% wet basis?

  1. 25.0 kg
  2. 22.3 kg
  3. 28.1 kg
  4. 29.8 kg
Answer and working

D. 29.8 kg

Dry matter = 500 × 0.89 = 445 kg. Final mass = 445/0.84 = 529.76 kg, so water to add = 29.8 kg. 25 kg (5% of 500) ignores that the total mass grows as water is added; 28.1 kg divides by the initial rather than the final (1 − M). 22.3 kg multiplies the dry matter by the 5-point rise (445 × 0.05).

Question 2 · hard

One tonne of maize at 30% moisture (dry basis) is dried to 12% moisture (wet basis). The water removed is closest to

  1. 180 kg
  2. 231 kg
  3. 205 kg
  4. 126 kg
Answer and working

D. 126 kg

Dry matter = 1000/(1 + 0.30) = 769.2 kg. Final mass at 12% wb = 769.2/0.88 = 874.1 kg. Water removed = 1000 − 874.1 = 125.9 kg. 180 kg subtracts percentages on mixed bases; 231 kg is the total water initially present, as if dried to zero moisture. 205 kg treats the initial 30% as wet basis.

Question 3 · medium

Air is at 30 °C and 50% RH (p_vs at 30 °C = 4.246 kPa). Given saturation pressures of 2.064 kPa at 18 °C and 2.198 kPa at 19 °C, its dew point is closest to

  1. 18.4 °C
  2. 18.0 °C
  3. 15.0 °C
  4. 30.0 °C
Answer and working

A. 18.4 °C

p_v = 0.5 × 4.246 = 2.123 kPa. The dew point is where p_vs = p_v: interpolating, 18 + (2.123 − 2.064)/(2.198 − 2.064) = 18.4 °C. The dew point equals the dry-bulb (30 °C) only at 100% RH. 18.0 °C takes the lower table value without interpolating; 15.0 °C halves the dry-bulb temperature.

Question 4 · hard

A tray holds 50 kg of dry solid on 2 m² and dries at a constant rate R_c = 1.5 kg/m²·h down to the critical moisture X_c = 0.6 (db); the rate then falls linearly to zero at X_e = 0.05. The falling-rate time from 0.6 to 0.15 kg/kg (db) is closest to

  1. 15.6 h
  2. 25.6 h
  3. 9.2 h
  4. 12.7 h
Answer and working

A. 15.6 h

t_f = [W_s(X_c − X_e)/(A R_c)] ln[(X_c − X_e)/(X − X_e)] = (50 × 0.55/3) × ln(0.55/0.10) = 9.167 × 1.7047 = 15.63 h. Dropping the log term gives 9.2 h; using total rather than free moisture in the log gives 12.7 h; 25.6 h is the total including the constant-rate period.

Question 5 · easy

The LSU dryer is best described as a

  1. rotary drum dryer heated through its shell
  2. continuous mixed-flow column dryer with alternate rows of inverted-V inlet and outlet ducts
  3. fluidised-bed dryer with a porous distributor plate
  4. batch in-bin dryer with a fully perforated floor and vertical stirring augers moving through the grain
Answer and working

B. continuous mixed-flow column dryer with alternate rows of inverted-V inlet and outlet ducts

Grain flows down by gravity past rows of inverted-V channels connected alternately to the hot-air plenum and the exhaust, and a fluted discharge roll sets the flow rate.

Question 6 · medium

1,000 kg of paddy at 13% moisture (wet basis) is soaked until it reaches 30% (wet basis). The water absorbed is closest to

  1. 211 kg
  2. 170 kg
  3. 243 kg
  4. 195 kg
Answer and working

C. 243 kg

Dry matter = 870 kg; soaked mass = 870/0.70 = 1242.9 kg; water absorbed = 242.9 kg. 170 kg subtracts percentages; dividing 170 by 0.87 uses the initial rather than the final (1 − M). 211 kg applies 0.17/0.70 to the 870 kg of dry matter instead of the 1000 kg.

Question 7 · easy

1,000 kg of paddy gives 520 kg of head rice and 130 kg of brokens. The head rice yield and total milled rice yield are

  1. 52% and 65%
  2. 65% and 52%
  3. 52% and 13%
  4. 80% and 65%
Answer and working

A. 52% and 65%

Both are on a paddy basis: head rice 520/1000 = 52%; total milled rice (520 + 130)/1000 = 65%. 80% is head rice as a share of milled rice (520/650), a different ratio.

Question 8 · medium

Broken rice kernels are separated from head rice in a modern mill mainly by

  1. magnetic separators
  2. indented cylinder length graders and sieves
  3. aspirators
  4. gravity tables
Answer and working

B. indented cylinder length graders and sieves

Brokens are shorter, so they lodge in the indents of a rotating cylinder and are lifted out. Gravity tables separate by density and aspirators by terminal velocity.

Question 9 · hard

A grain kernel has mass 30 mg, projected area 20 mm² and drag coefficient 0.5. With air density 1.2 kg/m³, its terminal velocity is closest to

  1. 49.0 m/s
  2. 5.0 m/s
  3. 2.2 m/s
  4. 7.0 m/s
Answer and working

D. 7.0 m/s

v_t = √[2mg/(ρ_a A C_d)] = √[2 × 3 × 10⁻⁵ × 9.81/(1.2 × 2 × 10⁻⁵ × 0.5)] = √49.05 = 7.00 m/s. Forgetting the factor 2 gives 4.95; omitting g gives 2.24; forgetting the square root gives 49.0.

Question 10 · hard

A crusher needs 10 kW to reduce a material from 20 mm to 5 mm. Assuming Kick's law, the power to reduce the same throughput from 20 mm to 2.5 mm is

  1. 18.3 kW
  2. 15.0 kW
  3. 23.3 kW
  4. 20.0 kW
Answer and working

B. 15.0 kW

Kick: E ∝ ln(L₁/L₂). Ratio = ln 8/ln 4 = 1.50, so P = 15.0 kW. Rittinger would give 23.3 kW and Bond 18.3 kW; doubling the power assumes energy proportional to size change.

A study plan for Post-Harvest Engineering of Cereals, Pulses & Oilseeds in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (62% of the 55 questions): Psychrometry and properties of air (9, 16%); Paddy and rice milling: husking, whitening, polishing and yields (7, 13%); Drying theory: constant and falling rate periods (6, 11%); Parboiling and hydrothermal treatment (6, 11%); Size reduction: Rittinger, Kick and Bond laws (6, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Cleaning, grading and screening effectiveness (4, 7%); Conveying: belt, bucket, screw and pneumatic (4, 7%); Moisture content: wet and dry basis (4, 7%); Thin-layer drying models (3, 5%); Equilibrium moisture content and sorption isotherms (2, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Grain dryers: bin, LSU, recirculating, fluidised-bed and solar (2, 4%); Oil expression and solvent extraction (1, 2%); Wheat milling (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Oil expression and solvent extraction (1 hard of 1), Wheat milling (1 hard of 1), Size reduction: Rittinger, Kick and Bond laws (4 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Equilibrium moisture content and sorption isotherms (1 easy of 2); Grain dryers: bin, LSU, recirculating, fluidised-bed and solar (1 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Post-Harvest Engineering of Cereals, Pulses & Oilseeds

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.