ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Units on post-harvest unit operations, process technology and machinery and design of processing machinery ask for PG depth: sorption models (GAB, BET, modified Henderson), thin-layer and diffusion models and effective diffusivity, deep-bed models, dryer design and performance indices, parboiling kinetics and quality, extraction and refining steps, and design relations for conveyors and mills.
Moisture, drying, parboiling, milling, cleaning, size reduction and conveying of grains, pulses and oilseeds.
Our 40 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 20 medium, 19 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
At a high-altitude site (lower barometric pressure), air with the same dry-bulb temperature and the same water-vapour partial pressure as at sea level has
A. a higher humidity ratio
W = 0.622 p_v/(P − p_v): a smaller P makes the denominator smaller, so W is higher. RH is p_v/p_vs, which depends only on temperature and p_v, so it is unchanged. This is why sea-level charts must be corrected. With p_v unchanged the dew point is also unchanged.
In the constant-rate period, the convective heat-transfer coefficient is 40 W/m²·K, the air is at 70 °C and its wet-bulb temperature is 35 °C. Taking latent heat as 2,400 kJ/kg, the drying rate is closest to
D. 2.10 kg/(m²·h)
R_c = h(T_a − T_wb)/λ = 40 × 35/2.4 × 10⁶ = 5.833e-04 kg/m²·s × 3600 = 2.10 kg/m²·h. Using the air temperature instead of the difference gives 4.20; leaving the answer per second is a unit slip. Using λ in kJ/kg with h in W gives a value 1,000 times too large (2100).
Treating a grain kernel as a sphere of radius 2 mm, the late-period plot of ln MR against time (s) has a slope of −1.2 × 10⁻⁴ s⁻¹. The effective moisture diffusivity is closest to
C. 4.86e-11 m²/s
First term of the sphere solution: ln MR = ln(6/π²) − (π²D/r²)t, so D = |slope|·r²/π² = 1.2 × 10⁻⁴ × (2 × 10⁻³)²/9.8696 = 4.86e-11 m²/s, within the usual 10⁻¹¹–10⁻¹⁰ range for grains. Omitting π² gives 4.80e-10; using the diameter instead of the radius gives a value four times too large.
Effective diffusivity of paddy is 3.0 × 10⁻¹¹ m²/s at 40 °C and 6.0 × 10⁻¹¹ m²/s at 60 °C. The Arrhenius activation energy is closest to
D. 30.1 kJ/mol
E_a = R ln(D₂/D₁)/(1/T₁ − 1/T₂) = 8.314 × 0.6931/(1/313.15 − 1/333.15) = 8.314 × 0.6931/1.9171e-04 = 30061 J/mol ≈ 30.1 kJ/mol. Using Celsius temperatures gives a nonsense small value; multiplying by 2.303 treats the natural log as a common log. 13.1 kJ/mol uses log₁₀ 2 instead of ln 2; 0.692 kJ/mol is the Celsius result; 69.2 kJ/mol multiplies by 2.303.
In the Page thin-layer model MR = exp(−k tⁿ), the exponent n
A. is an empirical shape parameter letting the curve depart from a simple exponential
Page added n to Lewis's exponential to improve fit; n = 1 reduces it to the Lewis model. It has no direct physical meaning, unlike k, which follows Arrhenius behaviour.
A three-parameter thin-layer model gives R² = 0.998 and a two-parameter model R² = 0.996 on the same data. The sound conclusion is that
A. RMSE, reduced chi-square and parameter count must also be weighed before preferring the first model
Adding parameters always raises R², so small gains are not evidence of a better model. Reduced chi-square and RMSE penalise extra parameters; physical plausibility also matters.
Smooth crushing rolls of 500 mm diameter are set with a 10 mm gap and fed 30 mm particles. The minimum coefficient of friction needed for the particles to be nipped is closest to
A. 0.283
cos b = (R + d)/(R + r) = (250 + 5)/(250 + 15) = 0.9623, so the half nip angle b = 15.79°, and μ ≥ tan b = 0.283. Using the full nip angle gives 0.615; using the full gap instead of half the gap gives 0.197. 0.272 is sin b instead of tan b.
Ground feed has a fineness modulus of 3.0. Using the Henderson–Perry relation D = 0.104 × 2^FM, the average particle size is closest to
D. 0.83 mm
D = 0.104 × 2³ = 0.832 mm. 0.0041 × 2^FM gives inches (0.0328 in), not millimetres; the other options misapply the exponent. 0.62 mm multiplies 2 by FM instead of raising it (0.104 × 6); 0.94 mm squares FM (0.104 × 3²).
A screw conveyor has a 0.30 m flight diameter, 0.06 m shaft, 0.30 m pitch, runs at 60 rpm with a loading factor of 0.30, and handles grain of 750 kg/m³. Its capacity is closest to
A. 16.5 t/h
Q = (π/4)(D² − d²)·p·N·ρ·φ = 0.7854 × (0.09 − 0.0036) × 0.30 × 60 × 750 × 0.30 = 274.8 kg/min = 16.5 t/h. Ignoring the shaft gives 17.2 t/h; ignoring the loading factor gives 55.0 t/h (a full trough). 0.27 t/h is the 274.8 kg/min read as t/min and mislabelled.
In horizontal dilute-phase pneumatic conveying of grain, if the air velocity falls below the saltation velocity,
C. particles drop out of suspension and form deposits or dunes in the pipe
Saltation velocity is the minimum horizontal velocity to keep particles suspended; below it they settle and can block the line. The vertical equivalent is the choking velocity.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.