ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Test procedure detail: lug curve and torque backup, drawbar test on track versus field, hydraulic lift through the range, static versus dynamic ROPS, noise and vibration evaluation, implement test indices (miss, multiple, quality of feed), and interpretation of test reports.
How tractors and implements are tested against codes, and how to read a test report.
Our 52 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 33 medium, 19 hard, across 12 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
A national tractor testing station wants formal recognition that its laboratories are technically competent to produce valid results. The international standard it is accredited to is
C. ISO/IEC 17025, competence of testing and calibration laboratories
Laboratory competence, including calibration traceability and measurement uncertainty, is covered by ISO/IEC 17025. ISO 9001 is a general quality management standard, ISO 14001 environmental management, and ISO 4254-1 a machinery safety standard, none of which accredits a testing laboratory's results.
OECD Codes 6 and 7 apply to
C. front-mounted and rear-mounted ROPS on narrow-track wheeled tractors
Codes 6 and 7 cover the roll bars of narrow-track tractors used in orchards and vineyards, front-mounted and rear-mounted respectively. Codes 3 and 4 are the dynamic and static tests for standard tractors, Code 8 covers track-layers, and Code 5 covers noise.
Report X gives a tractor's maximum PTO power measured under a national code; report Y gives another tractor's maximum PTO power under the OECD code. Before comparing the two numbers directly, the main thing to establish is
D. whether both codes define test conditions alike, as load steps and limits are code-specific
Two codes may define rated speed, test duration, permitted adjustments, atmospheric corrections and reported quantities differently, so the same tractor can give different numbers under each. A calibrated dynamometer of any make should give the same reading, and the year of a report does not by itself bias it.
With no drawbar load a tractor advances 4.2 m per revolution of its driving wheels. Under a heavy load it advances 3.6 m per revolution. The wheel slip is
D. 14.3 %
Slip = (advance unloaded − advance loaded)/advance unloaded × 100 = (4.2 − 3.6)/4.2 × 100 = 14.3 %. Dividing by the loaded advance gives 16.7 %; 85.7 % is the travel ratio; 6.0 simply scales the difference.
In a tractor drawbar test, maximum drawbar pull is normally obtained in the lowest gears while maximum drawbar power is obtained in a middle gear. The reason maximum pull is found in low gears is that
A. pull there is limited by wheel slip before the engine reaches full power
In low gears the high gear reduction can produce more axle torque than the tyres can transmit; the slip limit stops the run first. In middle gears the engine reaches maximum power at a useful speed, so drawbar power peaks there. Rolling resistance does not vanish at low speed, and the governor does not cut fuel by gear.
A gear pump of displacement 18 cm³/rev runs at 2000 rev/min. At the test pressure the measured delivery is 32.4 L/min. The volumetric efficiency is
A. 90 %
Theoretical delivery = 18 × 2000/1000 = 36 L/min. Volumetric efficiency = 32.4/36 = 90 %. 111 % is the inverse; 180 % divides by displacement without speed; 1.5 % mixes per-second and per-minute flow.
Three independent sources produce 84, 87 and 90 dB(A) at the driver's position. The combined level is
D. 92.4 dB(A)
L = 10 log₁₀(10^8.4 + 10^8.7 + 10^9.0) = 10 log₁₀(2.512e+08 + 5.012e+08 + 1.000e+09) = 92.4 dB(A). The arithmetic mean (87.0) and the loudest source alone (90) both ignore the added energy; the plain sum is meaningless.
During a static ROPS test, which observation alone is enough for the structure to fail?
D. Any part of the structure enters the operator's clearance zone during loading
A ROPS is meant to deform and absorb energy, so permanent bending is expected; failure is entry into the clearance zone, or fracture or mounting failure. Paint cracking and loading time are not acceptance criteria.
In the OECD ROPS codes, the energies to be absorbed and the crushing forces are set as functions of the tractor's reference mass. The reason is that
D. a heavier tractor carries more energy in an overturn and loads its structure more
The energy released in an overturn and the load on the structure when it supports the tractor scale with mass, so required energies and crushing forces rise with reference mass. The clearance zone is set from the seat, not cab size, and the ROPS protects the operator, not the engine.
Two tractor test reports give specific fuel consumption: tractor A 245 g/kWh at maximum power, tractor B 265 g/kWh at 50 per cent load. Before concluding that A is more efficient, the reader should
A. compare both at the same load, since SFC rises as the load falls
SFC is normally higher at part load, so B's figure at 50 per cent load cannot be compared with A's at full load. The reports give both tractors at several loads; compare like with like. g/kWh is the right comparative unit, and there is no standard correction of the kind in the other statements.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.