LAISHA
Open Laisha

GATE Farm Machinery Testing, Evaluation & Standards: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
35written to this exam in this subject
11syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery Testing, Evaluation & Standards in GATE

Section 3 tractor tests and performance: numerical answers on PTO power from dynamometer readings, specific fuel consumption, drawbar power, wheel slip, tractive efficiency, torque backup and field capacity. Answers are sensitive to km/h versus m/s, litres versus kilograms of fuel, and slip measured on the loaded rather than unloaded revolutions.

How tractors and implements are tested against codes, and how to read a test report.

Our 35 GATE questions in this subject: 6 easy, 21 medium, 8 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

At maximum PTO power of 35 kW a tractor uses 10 L/h of diesel. The fuel density is 0.84 kg/L. The specific fuel consumption is

  1. 240 g/kWh
  2. 286 g/kWh
  3. 340 g/kWh
  4. 326 g/kWh
Answer and working

A. 240 g/kWh

Mass flow = 10 × 0.84 = 8.4 kg/h = 8400 g/h. SFC = 8400 / 35 = 240 g/kWh. Treating litres as kilograms gives 286; dividing by density instead of multiplying gives 340; 326 comes from converting kW to metric horsepower the wrong way.

Question 2 · medium

A PTO test gives a torque of 150 N·m at rated engine speed and a maximum torque of 177 N·m at a lower speed. The torque backup is

  1. 15.3 %
  2. 18.0 %
  3. 84.7 %
  4. 118.0 %
Answer and working

B. 18.0 %

Torque backup = (T_max − T_rated)/T_rated × 100 = (177 − 150)/150 × 100 = 18.0 %. Dividing by the maximum torque gives 15.3 %; 84.7 and 118.0 are plain ratios, not the rise.

Question 3 · hard

A PTO torque of 400 N·m is measured at 540 rev/min PTO speed with the engine at 2100 rev/min. Ignoring losses between engine and PTO, the equivalent crankshaft torque is

  1. 1555.6 N·m
  2. 400.0 N·m
  3. 102.9 N·m
  4. 51.4 N·m
Answer and working

C. 102.9 N·m

Power is the same at both shafts, so T_engine = T_PTO × (N_PTO/N_engine) = 400 × 540/2100 = 102.9 N·m. Multiplying by the inverse ratio gives 1555.6 N·m, which would mean the engine is slower than the PTO; 400 N·m ignores the speed ratio entirely; 51.4 N·m is half the correct value.

Question 4 · easy

In a drawbar test a tractor pulls 25 kN at 7.2 km/h. The drawbar power is

  1. 180.0 kW
  2. 50.0 kW
  3. 13.9 kW
  4. 5.0 kW
Answer and working

B. 50.0 kW

P = pull × speed = 25 kN × 7.2/3.6 m/s = 25 × 2.0 = 50.0 kW. Forgetting to convert km/h gives 180 kW; dividing by 3.6 twice gives 13.9; dividing by 36 gives 5.0.

Question 5 · hard

A tractor's theoretical (no-slip) speed in a given gear is 8 km/h. Pulling 20 kN it runs at 15 % wheel slip. Its drawbar power is

  1. 44.4 kW
  2. 37.8 kW
  3. 52.3 kW
  4. 6.7 kW
Answer and working

B. 37.8 kW

Actual speed = 8 × (1 − 0.15) = 6.8 km/h. Drawbar power = 20 × 6.8/3.6 = 37.8 kW. Ignoring slip gives 44.4 kW; dividing by (1 − slip) gives 52.3; 6.7 kW is the power lost to slip, not delivered.

Question 6 · hard

A burette shows that an engine uses 50 cm³ of diesel in 18 s. The fuel density at the measured fuel temperature is 0.83 g/cm³. The fuel mass flow is

  1. 8.30 kg/h
  2. 10.00 kg/h
  3. 12.05 kg/h
  4. 0.138 kg/h
Answer and working

A. 8.30 kg/h

Volume flow = 50/18 = 2.778 cm³/s = 10.0 L/h. Mass flow = 10.0 × 0.83 = 8.30 kg/h. 10.00 treats litres as kilograms; 12.05 divides by density; 0.138 is per minute, not per hour.

Question 7 · easy

A cultivator with a working width of 1.8 m operates at 4.5 km/h. Its theoretical field capacity is

  1. 0.81 ha/h
  2. 8.1 ha/h
  3. 0.081 ha/h
  4. 2.25 ha/h
Answer and working

A. 0.81 ha/h

TFC = w × v/10 = 1.8 × 4.5/10 = 0.81 ha/h (because 1 km × 1 m = 1000 m² = 0.1 ha). 8.1 omits the /10; 0.081 divides by 100; 2.25 wrongly converts to m/s.

Question 8 · medium

A 3-bottom mouldboard plough, each bottom 30 cm wide, works at 18 cm depth with a measured draft of 12 kN. Its specific draft is

  1. 22.2 N/cm²
  2. 0.741 N/cm²
  3. 133 N/cm²
  4. 7.41 N/cm²
Answer and working

D. 7.41 N/cm²

Furrow area = 3 × 30 × 18 = 1620 cm². Specific draft = 12000 N/1620 cm² = 7.41 N/cm². Using one bottom's area gives 22.2; 0.741 is a decimal slip; 133 divides by total width alone, which is draft per cm of width.

Question 9 · medium

A thresher is fed crop containing 500 kg of grain in total. Unthreshed grain collected from all outlets amounts to 6 kg. The threshing efficiency is

  1. 1.2 %
  2. 97.6 %
  3. 94.0 %
  4. 98.8 %
Answer and working

D. 98.8 %

Threshing efficiency = (1 − unthreshed/total) × 100 = (1 − 6/500) × 100 = 98.8 %. 1.2 % is the unthreshed fraction; 97.6 % subtracts the loss twice; 94.0 % subtracts the kilograms of unthreshed grain as if they were a percentage.

Question 10 · medium

A tractor will work 600 hours a year at an average PTO load of 20 kW. Its test report gives a specific energy of 2.8 kWh/L at that load. The expected annual fuel use is

  1. 33600 L
  2. 214 L
  3. 4286 L
  4. 3600 L
Answer and working

C. 4286 L

Energy = 20 × 600 = 12000 kWh. Fuel = 12000/2.8 = 4286 L. Multiplying by specific energy gives 33600; leaving out power gives 214; 3600 wrongly applies a density to a value already in litres.

A study plan for Farm Machinery Testing, Evaluation & Standards in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (60% of the 35 questions): PTO performance test (6, 17%); Drawbar performance test (5, 14%); Laboratory and field tests of tillage and sowing equipment (5, 14%); Test instrumentation: dynamometers and fuel meters (5, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Hydraulic lift test (3, 9%); Tests of sprayers and harvesting equipment (3, 9%); Brake and turning tests (2, 6%); Interpreting test reports (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Noise at the operator's ear (2, 6%); Test codes: OECD, BIS, PAES/PNS, ASABE and ISO (1, 3%); Types of tests: commercial, batch, confidential and prototype (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Brake and turning tests (1 hard of 2), PTO performance test (2 hard of 6), Hydraulic lift test (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Test codes: OECD, BIS, PAES/PNS, ASABE and ISO (1 easy of 1); Types of tests: commercial, batch, confidential and prototype (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Farm Machinery Testing, Evaluation & Standards

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.