GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papersGATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.
Source: gate2027.iitm.ac.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Numerical-answer and MCQ items in Section 4: manometer readings, force and centre of pressure on gates, venturimeter discharge, Darcy-Weisbach head loss and laminar flow, pipes in series and parallel, V-notch and rectangular weir discharge, Manning uniform flow, the best hydraulic section, critical depth and specific energy, hydraulic jump sequent depth and energy loss, and Froude model scaling. Most items need a calculator and careful units.
Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.
Our 87 GATE questions in this subject: 11 easy, 53 medium, 23 hard, across 18 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE and are not shown on any other exam's page.
A U-tube mercury manometer (relative density 13.6) is connected to a pipe carrying water; the other limb is open to air. The pipe centre is 0.2 m above the mercury surface in the pipe-side limb, and the mercury in the open limb stands 0.3 m above that surface. What is the gauge pressure at the pipe centre?
C. 38.1 kPa
Start at the pipe centre and move to the open surface: p_A + ρ_w g(0.2) − ρ_Hg g(0.3) = 0, so p_A = 13 600 × 9.81 × 0.3 − 1000 × 9.81 × 0.2 = 40025 − 1962 = 38063 Pa ≈ 38.1 kPa. Adding the water column gives 42.0 kPa; ignoring it gives 40.0 kPa. 35.1 kPa counts the whole 0.5 m (0.2 + 0.3 m) as a water column on the pipe side.
A vertical rectangular gate 1.5 m wide and 2 m high has its top edge 1 m below the water surface. At what depth below the water surface does the resultant hydrostatic force act?
A. 2.17 m
h_cp = h̄ + I_G/(A h̄). h̄ = 2 m, A = 3 m², I_G = bd³/12 = 1.5 × 8/12 = 1.00 m⁴. h_cp = 2 + 1/(3 × 2) = 2.17 m. The centre of pressure is always below the centroid (2.00 m); forgetting to divide by h̄ gives 2.33 m. 1.83 m subtracts I_G/(A h̄) and so puts the centre of pressure above the centroid.
Oil (density 900 kg/m³, dynamic viscosity 0.2 Pa·s) flows at a mean velocity of 1 m/s through 100 m of 100 mm pipe. What is the friction head loss?
D. 7.25 m of oil
Re = ρVD/μ = 900 × 1 × 0.1/0.2 = 450, laminar. Hagen-Poiseuille: h_f = 32μVL/(ρgD²) = 32 × 0.2 × 1 × 100/(900 × 9.81 × 0.01) = 7.25 m. The same comes from f = 64/Re = 0.142 in Darcy-Weisbach. Assuming a turbulent f = 0.02 gives 1.02 m, far too low. 3.62 m uses 16 instead of 32 in Hagen-Poiseuille; 14.5 m uses 64.
An Indian textbook writes the pipe friction loss as h_f = 4fLV²/(2gD) and quotes f = 0.005. What is the equivalent Darcy friction factor used in h_f = fLV²/(2gD)?
B. 0.020
The 4f form uses the Fanning coefficient, which is one quarter of the Darcy factor. 4 × 0.005 = 0.020. Mixing the two forms is a common source of answers four times too large or too small. 0.00125 divides by 4 instead of multiplying; 0.010 doubles the Fanning value.
Use the Swamee-Jain equation to estimate the Darcy friction factor for turbulent flow at Re = 2 × 10⁵ in a pipe of relative roughness ε/D = 0.001.
A. 0.0212
f = 0.25/[log₁₀(ε/3.7D + 5.74/Re^0.9)]² = 0.25/[log₁₀(0.000270 + 0.0000973)]² = 0.0212. The Blasius smooth-pipe value, 0.316/Re^0.25 = 0.0149, ignores roughness; 64/Re applies only to laminar flow. 0.000320 is 64/Re, valid only for laminar flow; 0.00530 is the Fanning value (one quarter of Darcy).
A single 300 mm pipe is to be replaced by two identical pipes laid in parallel, of the same length, carrying the same total discharge with the same head loss and friction factor. What diameter should each new pipe be?
D. 227 mm
Each new pipe carries Q/2 at the same head loss: (Q/2)²/d⁵ = Q²/D⁵, so d⁵ = D⁵/4 and d = D/4^0.2 = D/2^0.4 = 0.758D = 227 mm. Keeping the same total area (D/√2 = 212 mm) is not enough, because smaller pipes lose more head per unit flow. 261 mm takes the fifth root of 2 instead of 4; 150 mm simply halves the diameter.
A 90° V-notch with C_d = 0.6 is used to measure a tubewell's discharge. The head over the vertex is 0.2 m. What is the discharge?
D. 25.4 L/s
Q = (8/15) C_d √(2g) tan(θ/2) H^2.5 = (8/15) × 0.6 × 4.429 × tan 45° × 0.2^2.5 = 1.417 × 0.0179 = 0.0254 m³/s = 25.4 L/s. Using H^1.5 gives 127 L/s, a large overestimate. 56.7 L/s uses H² instead of H^2.5; 31.7 L/s uses the rectangular 2/3 instead of 8/15.
The head over a triangular notch is measured with an error of 2 per cent. What is the resulting percentage error in the computed discharge?
D. 5 %
Q ∝ H^2.5, so dQ/Q = 2.5 dH/H = 2.5 × 2 = 5 %. For a rectangular weir (Q ∝ H^1.5) it would be 3 %, which is why head must be measured more precisely on a V-notch. 4 % uses an exponent of 2.
If both the bed width and the side slope of a trapezoidal channel are free to be chosen, what shape is the most economical section?
B. Half a regular hexagon, with sides at 60° to the horizontal
Optimising side slope as well as width gives z = 1/√3 (sides at 60°), with the bed and the sloping sides of equal length: half a regular hexagon. The b = 2y rectangle is the best only among rectangles.
For a given discharge in an open channel, what is true of the flow at critical depth?
B. The specific energy is a minimum
On the specific-energy curve for a fixed q, the critical depth is the point of minimum E; equivalently, for a fixed E, discharge is maximum there. In a rectangular channel the velocity head at critical depth is y_c/2, not y_c, and Fr = 1.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.