Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) · India · Tamil Nadu Public Service Commission
Original practice questions written to the published syllabus · not past papersTamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) is a government recruitment exam run by Tamil Nadu Public Service Commission, for candidates in India. Degree-standard subject paper (for posts such as Assistant Engineer (Agri)).
Source: tnpsc.gov.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.
Our 44 Tamil Nadu PSC questions in this subject: 26 easy, 16 medium, 2 hard, across 17 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Tamil Nadu PSC and are not shown on any other exam's page.
In the Hazen-Williams equation, what does a higher value of the coefficient C indicate?
B. A smoother pipe with lower friction loss
C sits in the denominator of the head-loss form, h_f ∝ 1/C^1.852, so a larger C means less loss, i.e. a smoother pipe. Plastic pipe has high C (around 140–150); old tuberculated iron much lower. C does not represent diameter or fluid properties; the equation is for water only.
Replacing a sharp-edged pipe entrance from a tank with a well-rounded bell-mouth entrance changes the entrance loss coefficient roughly:
D. From about 0.5 to about 0.05 or less
A sharp (square-edged) entrance causes a vena contracta and re-expansion, K ≈ 0.5. Rounding the edge suppresses separation, reducing K to about 0.05 or less. A projecting (re-entrant) pipe is worse, around 0.8–1.0.
A pipeline consists of 400 m of 200 mm pipe followed by 300 m of 150 mm pipe. Neglecting minor losses and taking the same friction factor throughout, what length of 200 mm pipe is hydraulically equivalent?
D. 1664 m
Dupuit: L/D⁵ = ΣLᵢ/Dᵢ⁵, so L = 400 + 300 × (0.2/0.15)⁵ = 400 + 300 × 4.21 = 1664 m. Simply adding lengths (700 m) ignores the much higher loss in the smaller pipe; using D² or D³ understates it. 933 m scales by D² and 1111 m by D³.
For pipes connected in series, which quantity is the same in every pipe?
D. The discharge
In series the same flow passes through each pipe in turn and the losses add. In parallel the head loss is the same in each branch and the flows add. Velocity and Re change with diameter.
A broad-crested weir 3 m long carries water under a head of 0.5 m above the crest (neglect approach velocity, take C_d = 1). What is the maximum discharge?
B. 1.81 m³/s
Flow passes through critical depth on the crest, h = 2H/3, giving Q = 1.705 C_d L H^1.5 = 1.705 × 3 × 0.5^1.5 = 1.81 m³/s. The sharp-crested constant 1.84 gives 1.95 m³/s; taking the depth on the crest as H itself gives 3.32 m³/s. 0.904 m³/s uses H^2.5 instead of H^1.5.
Using the Chezy equation with C = 50 m^0.5/s, what is the mean velocity in a channel with hydraulic radius 0.8 m and bed slope 0.0004?
A. 0.894 m/s
V = C√(RS) = 50 × √(0.8 × 0.0004) = 50 × 0.0179 = 0.894 m/s. Mixing in Manning's R^(2/3) gives 0.862 m/s. 0.0160 m/s multiplies C × R × S and forgets the square root.
An earthen trapezoidal canal has bed width 4 m, side slopes 2 horizontal to 1 vertical, bed slope 0.0003 and Manning's n = 0.022. What discharge does it carry at a uniform depth of 1.5 m?
D. 8.16 m³/s
A = (b + zy)y = (4 + 3) × 1.5 = 10.5 m²; P = b + 2y√(1 + z²) = 4 + 3√5 = 10.7 m; R = 0.981 m. Q = (A/n)R^(2/3)S^(1/2) = (10.5/0.022) × 0.987 × 0.0173 = 8.16 m³/s. Taking the sloping side length as zy instead of y√(1 + z²) gives 8.54 m³/s; using the top width in the area gives 14.8 m³/s. 0.141 m³/s uses S instead of √S.
A wide rectangular channel carries a discharge of 3 m³/s per metre of width. What is the critical depth, and the minimum specific energy?
A. y_c = 0.972 m; E_min = 1.46 m
y_c = (q²/g)^(1/3) = (9/9.81)^(1/3) = 0.972 m. At critical depth the velocity head is y_c/2, so E_min = 1.5 y_c = 1.46 m. Forgetting to square q gives 0.674 m; a square root instead of cube root gives 0.958 m.
Water flows at 3 m/s with a depth of 0.5 m in a rectangular channel. What is the Froude number and the flow regime?
C. 1.35; supercritical
Fr = V/√(gy) = 3/√(9.81 × 0.5) = 1.35. Fr > 1 means supercritical (rapid) flow; surface waves cannot travel upstream. Using √(2gy), the jet-velocity form, gives 0.958 and the wrong regime.
A hydraulic jump forms in a horizontal rectangular channel. The depth before the jump is 0.4 m and the upstream Froude number is 5. What is the sequent depth after the jump?
A. 2.64 m
y₂/y₁ = ½[√(1 + 8Fr₁²) − 1] = ½[√201 − 1] = 6.59. y₂ = 0.4 × 6.59 = 2.64 m. Forgetting to square Fr₁ gives 1.08 m. 3.04 m uses + 1 instead of − 1 in the bracket; 2.00 m multiplies y₁ by Fr₁.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.