LAISHA
Open Laisha

Agricultural and Biosystems Engineers Licensure Examination Machine Design: practice questions

Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC

Original practice questions written to the published syllabus · not past papers
10worked here, free
42written to this exam in this subject
11syllabus units

About Agricultural and Biosystems Engineers Licensure Examination

Agricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.

Source: prc.gov.ph.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Machine Design in Agricultural and Biosystems Engineers Licensure Examination

Machine design and analysis under power and machinery: shaft, key, belt, chain, gear, bearing and spring calculations with standard formulas and non-programmable calculators.

Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.

Our 42 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 13 easy, 23 medium, 6 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.

Question 1 · easy

Bolts on a vibrating seed drill frame keep working loose. Which measure is most effective in preventing loosening?

  1. Greasing the threads and tightening by hand
  2. Using a bolt of lower strength grade so it can stretch and keep gripping the nut as the frame vibrates
  3. Tightening the bolts to the correct preload, with a locking device such as a prevailing-torque nut
  4. Using a thinner nut
Answer and working

C. Tightening the bolts to the correct preload, with a locking device such as a prevailing-torque nut

Adequate preload keeps the joint surfaces from slipping, which is what lets a nut rotate under vibration; a locking device adds security. A thinner nut or weaker bolt cannot hold the preload, and hand tightening gives too little.

Question 2 · medium

A plate is joined by two transverse fillet welds with 10 mm legs and carries 60 kN. Using the textbook convention of tensile stress on the throat with an allowable of 80 MPa, what length is needed for each weld?

  1. 53.0 mm
  2. 26.5 mm
  3. 106.1 mm
  4. 37.5 mm
Answer and working

A. 53.0 mm

For two transverse fillets P = 2 x 0.707 h l sigma = 1.414 h l sigma, so l = 60000/(1.414 x 10 x 80) = 53.0 mm each. Using leg size instead of throat gives 37.5 mm (unsafe); treating one weld alone gives 106.1 mm; dividing again by two for the two welds after already using 1.414 gives 26.5 mm.

Question 3 · easy

For a fillet weld with equal legs of size h, the throat thickness used in strength calculations is:

  1. 0.707 h
  2. 0.5 h
  3. h
  4. 1.414 h
Answer and working

A. 0.707 h

The throat is the shortest distance from the root to the face of a 45-degree fillet: h cos 45 = 0.707 h. Stress is calculated on this smallest section. 1.414 h appears only when two welds are added together.

Question 4 · medium

What is the Wahl stress factor for a helical spring of spring index 6?

  1. 1.083
  2. 1.103
  3. 1.252
  4. 1.150
Answer and working

C. 1.252

K = (4C - 1)/(4C - 4) + 0.615/C = 23/20 + 0.615/6 = 1.150 + 0.1025 = 1.252. The direct-shear factor Ks = 1 + 0.5/C = 1.083 ignores curvature; dropping the 0.615/C term gives 1.150. 1 + 0.615/C = 1.103 keeps only the curvature correction.

Question 5 · easy

Two springs of stiffness 20 N/mm and 30 N/mm are connected in series. What is the combined stiffness?

  1. 25 N/mm
  2. 12 N/mm
  3. 50 N/mm
  4. 0.083 N/mm
Answer and working

B. 12 N/mm

In series both springs carry the same force and the deflections add: 1/k = 1/20 + 1/30, so k = 20x30/(20+30) = 12 N/mm. 50 N/mm is the parallel result. 25 N/mm is the simple average; 0.083 N/mm stops at 1/20 + 1/30 without inverting.

Question 6 · medium

A deep-groove ball bearing has a basic dynamic load rating of 30 kN and carries an equivalent load of 5 kN at 1000 rpm. What is its L10 life in hours?

  1. 6542 h
  2. 100 h
  3. 3600 h
  4. 216000 h
Answer and working

C. 3600 h

L10 = (C/P)^3 = (30/5)^3 = 216 million revolutions. Hours = 216 x 10^6/(60 x 1000) = 3600 h. The exponent 10/3 applies to roller bearings (6542 h); forgetting the 60 gives minutes; using exponent 1 gives 100 h.

Question 7 · medium

A farmer keeps breaking shear bolts on a post-hole digger in stony ground and replaces them with high-tensile bolts. A week later the gearbox fails. What is the correct advice?

  1. Weld the flange to the hub to remove the bolt
  2. Use only the specified shear bolt grade and size; if bolts break often, reduce the load or fit an auto-reset slip clutch
  3. Grease the shear bolt so it breaks less often
  4. Use an even stronger bolt so it never breaks, since the gearbox failure shows the driveline needs a stiffer, stronger connection
Answer and working

B. Use only the specified shear bolt grade and size; if bolts break often, reduce the load or fit an auto-reset slip clutch

The shear bolt is sized to fail below the gearbox's damaging torque. A stronger bolt moves the weak link to the gearbox, which is what happened. The fix is the correct bolt and, where overloads are frequent, a self-resetting device. Welding removes protection altogether.

Question 8 · medium

In welding a trailer drawbar, what is the heat-affected zone (HAZ)?

  1. The parent metal next to the weld whose structure and properties have been changed by the welding heat without melting
  2. The area where slag collects on the weld surface
  3. The weld metal deposited from the electrode
  4. The part of the joint that is preheated with a torch before welding, so that its hardness zone is set before the arc is struck
Answer and working

A. The parent metal next to the weld whose structure and properties have been changed by the welding heat without melting

The HAZ is base metal heated enough to change its microstructure (it can harden and become brittle in higher-carbon steels) but not melted. Weld metal is the fused zone; slag is flux residue; preheating is a procedure that reduces HAZ hardening.

Question 9 · medium

Why is a split-muff (clamp) coupling preferred to a solid muff coupling in some line-shaft drives?

  1. It absorbs shock through rubber bushes
  2. It can be fitted or removed without moving the shafts axially
  3. It needs no key
  4. It can connect shafts at an angle
Answer and working

B. It can be fitted or removed without moving the shafts axially

The clamp coupling is split along the axis and bolted together, so it can be installed on shafts already in place. It is still a rigid coupling needing aligned shafts; rubber-bushed couplings absorb shock, and Hooke's joints connect intersecting shafts.

Question 10 · medium

A V-belt drive on a chaff cutter squeals and the belts glaze within weeks. The pulleys are aligned. Which cause is most likely and what is the fix?

  1. Belt dressing oil should be applied weekly
  2. The belts are too tight (over-tensioned); loosen until they flap
  3. The belts are slipping because of too little tension (or a worn groove); retension to the specified value and replace worn pulleys
  4. A flat belt should replace the V-belts to increase grip
Answer and working

C. The belts are slipping because of too little tension (or a worn groove); retension to the specified value and replace worn pulleys

Squeal and glazing are signs of slip, which heats and hardens the belt surface. Correct tension and sound grooves (a belt riding low in a worn groove loses the wedge action) stop it. Loose, flapping belts slip more, oil on belts is harmful, and a flat belt grips less than a V-belt.

A study plan for Machine Design in Agricultural and Biosystems Engineers Licensure Examination

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (57% of the 42 questions): Belt and chain drives (10, 24%); Springs (6, 14%); Keys and couplings (4, 10%); Spur gear design (Lewis and Buckingham) (4, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Bolted joints (3, 7%); Overload safety devices: shear bolts and slip clutches (3, 7%); Shafts under combined bending and torsion (3, 7%); The design process, materials and factor of safety (3, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Welded joints (3, 7%); Rolling and sliding bearings and bearing life (2, 5%); Knuckle and cotter joints (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Keys and couplings (2 hard of 4), Rolling and sliding bearings and bearing life (1 hard of 2), Belt and chain drives (3 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Bolted joints (2 easy of 3); The design process, materials and factor of safety (2 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Agricultural and Biosystems Engineers Licensure Examination Machine Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.