LAISHA
Open Laisha

ICAR AIEEA-PG Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
50written to this exam in this subject
15syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in ICAR AIEEA-PG

Recall of implement parts and functions (plough bottoms, suction, disc and tilt angles, metering devices, openers), classification of tillage, transplanter features, and short calculations of field capacity, seed rate and cost.

Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.

Our 50 ICAR AIEEA-PG questions in this subject: 9 easy, 40 medium, 1 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

Which mouldboard shape lays a sod furrow slice over with the least breaking?

  1. Cylindrical (stubble) mouldboard
  2. Slatted mouldboard
  3. Helicoidal (sod or breaker) mouldboard
  4. High-speed digger mouldboard
Answer and working

C. Helicoidal (sod or breaker) mouldboard

A long, gently twisted helicoidal mouldboard turns the slice over slowly with little pulverising, suiting sod. A cylindrical, steep mouldboard breaks and pulverises the slice; slatted boards reduce contact in sticky soils.

Question 2 · medium

The disc angle of a disc plough is the angle between

  1. the plane of the disc and the vertical, measured in the vertical transverse plane
  2. the plane of the disc edge and the direction of travel, in the horizontal plane
  3. the disc axle and the tractor rear axle in side view
  4. the disc face and the furrow wall
Answer and working

B. the plane of the disc edge and the direction of travel, in the horizontal plane

Disc angle is measured horizontally from the direction of travel; tilt angle is measured between the disc plane and the vertical. Confusing the two is the usual error.

Question 3 · easy

A chisel plough differs from a mouldboard plough mainly in that it

  1. inverts the slice completely
  2. needs PTO drive
  3. shatters and loosens soil without inverting it
  4. is used only for puddling
Answer and working

C. shatters and loosens soil without inverting it

Chisel shanks loosen and shatter soil and leave residue on the surface, which is why they suit conservation tillage. Mouldboards invert; rotary tillers need PTO drive.

Question 4 · medium

Subsoiling a hardpan is most effective when the soil at working depth is

  1. dry enough to shatter
  2. saturated so the tine slides easily
  3. frozen solid to below the tine
  4. freshly irrigated and soft
Answer and working

A. dry enough to shatter

Dry, brittle subsoil fractures and loosens around the tine. Wet subsoil deforms plastically, so the tine cuts a slot and smears the walls with little loosening.

Question 5 · medium

Why are zero-till drills built with heavier frames and stronger openers than drills for a tilled seedbed?

  1. They carry more seed
  2. They work at higher speed
  3. They must cut residue and penetrate untilled, firmer soil
  4. They meter by vacuum
Answer and working

C. They must cut residue and penetrate untilled, firmer soil

Untilled soil is stronger and covered with residue, so openers need more down-force and robust construction.

Question 6 · medium

Why do pneumatic (vacuum) meters handle ungraded seed better than cell plates?

  1. They meter by volume, so a fixed volume of seed is dropped regardless of size
  2. They use larger cells
  3. Seeds are held on holes by suction, so seed size need not match a cell
  4. They need no singulator
Answer and working

C. Seeds are held on holes by suction, so seed size need not match a cell

Suction holds a seed on each hole regardless of small variations in shape, and a singulator removes doubles, so exact grading matters less than for a fixed cell.

Question 7 · medium

In a central-hopper air seeder, how is seed divided among many rows?

  1. Each row has its own vacuum disc
  2. Each opener has its own separate hopper and fluted roller driven by a ground wheel
  3. Seed is broadcast and harrowed in
  4. A single meter feeds an air stream that a distribution head splits into hoses
Answer and working

D. A single meter feeds an air stream that a distribution head splits into hoses

Air seeders meter centrally and blow seed to a distribution head that divides it among the row hoses, allowing very wide machines.

Question 8 · easy

Most mechanical rice transplanters require seedlings raised as

  1. wet-bed nursery seedlings pulled and bundled
  2. a mat nursery
  3. direct-seeded plants
  4. plug seedlings in deep cells only
Answer and working

B. a mat nursery

The picking fork cuts blocks from a mat, so seedlings must be grown densely on a thin soil layer forming a mat. The roots interlock so the mat holds together when the fork cuts it.

Question 9 · medium

At 30 mm exposed flute length a fluted-roller drill delivers 120 kg/ha. Assuming delivery proportional to exposed length, what length gives 100 kg/ha?

  1. 25 mm
  2. 36 mm
  3. 5 mm
  4. 10 mm
Answer and working

A. 25 mm

Length ∝ rate: 30 × 100/120 = 25 mm. Inverting the ratio gives 36 mm, which would increase the rate. The proportional assumption fails at short exposures, so recheck by calibration. 5 mm is the reduction (30 × 20/120), not the new length; 10 mm subtracts the 20 kg/ha change as if it were millimetres.

Question 10 · easy

Using interest on average investment, what is the annual interest charge on an implement costing 400 000 with salvage value 40 000 at 10 % interest?

  1. 22,000
  2. 40,000
  3. 18,000
  4. 44,000
Answer and working

A. 22,000

Average investment = (400 000 + 40 000)/2 = 220 000; interest = 220 000 × 0.10 = 22,000. Charging on full price gives 40,000; using (P − S)/2 gives 18,000. 44,000 adds P and S without halving.

A study plan for Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 50 questions): Seed-metering mechanisms: fluted roller, cup, plate and pneumatic (6, 12%); Forces on tillage tools, draft and hitching (5, 10%); Paddy and vegetable transplanters (5, 10%); Cost analysis of implements (4, 8%); Calibration of seed drills (3, 6%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Chisel plough and subsoiler (3, 6%); Disc plough (3, 6%); Fertiliser distributors (3, 6%); Field capacity and field efficiency (3, 6%); Furrow openers (3, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Harrows, cultivators and rotavators (3, 6%); Mouldboard plough (3, 6%); Seed drills and planters (3, 6%); Objectives and types of tillage (2, 4%); Furrow geometry (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Seed drills and planters (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Objectives and types of tillage (1 easy of 2); Paddy and vegetable transplanters (2 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.