LAISHA
Open Laisha

Nepal Engineering Council Registration Exam Building Materials, Theory of Structures & Construction: practice questions

Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council

Original practice questions written to the published syllabus · not past papers
10worked here, free
78written to this exam in this subject
9syllabus units

About Nepal Engineering Council Registration Exam

Nepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.

Official site: nec.gov.np.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Building Materials, Theory of Structures & Construction in Nepal Engineering Council Registration Exam

Materials, structural members, foundations and estimates for farm buildings and small works.

Our 78 Nepal Engineering Council Registration Exam questions in this subject: 31 easy, 34 medium, 13 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.

Question 1 · easy

In English bond brickwork, how are headers and stretchers arranged?

  1. Every course is laid with stretchers only, offset by half a brick
  2. Each course has headers and stretchers alternating along its length
  3. Every course is laid with headers only, offset by a quarter brick
  4. Alternate courses are entirely headers and entirely stretchers
Answer and working

D. Alternate courses are entirely headers and entirely stretchers

English bond has a full course of headers, then a full course of stretchers, and is regarded as the strongest bond for walls one brick thick or more. Headers and stretchers alternating within each course is Flemish bond; all-stretcher is stretcher bond (half-brick walls); all-header is header bond (curved walls).

Question 2 · medium

Brick earth that contains too much lime is used to make bricks. What is the most likely result?

  1. The bricks melt and lose shape in burning, and lime lumps may later split them
  2. The bricks turn bright red because lime reacts with the iron oxide during firing
  3. The bricks become very porous and light because the lime burns out completely
  4. The bricks crack during drying because lime can make the clay too plastic to shape
Answer and working

A. The bricks melt and lose shape in burning, and lime lumps may later split them

Excess lime acts as a flux, so bricks fuse and distort in the kiln; lumps of lime become quicklime that slakes and expands when wet, splitting the brick. Plasticity comes from alumina, not lime, and the red colour comes from iron oxide; lime tends to make bricks lighter in colour.

Question 3 · medium

How does a pozzolana such as fly ash or rice-husk ash contribute to the strength of a lime or blended-cement binder?

  1. Its reactive silica combines with calcium hydroxide and water to form calcium silicate hydrate
  2. It reacts with atmospheric carbon dioxide to form calcium carbonate, as fat lime does
  3. It hydrates on its own like Portland cement clinker, producing calcium hydroxide and heat
  4. It fills voids as an inert powder only, so any strength gain is due to better particle packing
Answer and working

A. Its reactive silica combines with calcium hydroxide and water to form calcium silicate hydrate

A pozzolana has little or no cementing value alone; it reacts with calcium hydroxide (from lime or from cement hydration) to form extra C–S–H. It does not hydrate on its own like clinker, and the carbonation route is how fat lime hardens, not how a pozzolana works. Packing (filler) effects exist but are not the main mechanism.

Question 4 · medium

A batch needs 0.42 m³ of dry sand by volume. The damp site sand shows 25% bulking. What volume of damp sand should be measured out?

  1. 0.336 m³
  2. 0.420 m³
  3. 0.525 m³
  4. 0.315 m³
Answer and working

C. 0.525 m³

Bulked volume = dry volume × (1 + bulking) = 0.42 × 1.25 = 0.525 m³. Dividing by 1.25 (0.336) or using 0.75 (0.315) corrects in the wrong direction and leaves the mix short of sand; measuring 0.420 m³ ignores bulking altogether.

Question 5 · hard

A singly reinforced beam is 250 mm wide with effective depth 450 mm, M25 concrete and Fe415 steel. What is its limiting moment of resistance Mu,lim by IS 456?

  1. 139.7 kN·m
  2. 218.7 kN·m
  3. 169.1 kN·m
  4. 174.6 kN·m
Answer and working

D. 174.6 kN·m

xu,max = 0.48 × 450 = 216 mm. Mu,lim = 0.36 fck b xu,max (d − 0.42 xu,max) = 0.36 × 25 × 250 × 216 × (450 − 90.72) = 174.6 kN·m (≈ 0.138 fck b d²). Using 0.46 (the Fe500 limit) gives 169.1; omitting the 0.42 xu lever-arm reduction gives 218.7. 139.7 kN·m uses fck = 20 (M20) instead of 25.

Question 6 · hard

What development length does IS 456 give for a 20 mm Fe500 deformed bar in tension in M20 concrete? (Design bond stress for plain bars in M20 is 1.2 MPa, increased by 60% for deformed bars.)

  1. 1302 mm
  2. 1133 mm
  3. 1812 mm
  4. 940 mm
Answer and working

B. 1133 mm

τbd = 1.2 × 1.6 = 1.92 MPa. Ld = φ σs/(4 τbd) = 20 × 0.87 × 500/(4 × 1.92) = 1133 mm (about 57φ). Using 1.2 MPa (plain bars) gives 1812; omitting 0.87 gives 1302; 940 is the Fe415 value.

Question 7 · hard

A short, axially loaded 350 × 350 mm column has four 20 mm Fe500 bars and M25 concrete. Using Pu = 0.4 fck Ac + 0.67 fy Asc (IS 456), what is its design capacity?

  1. 1823 kN
  2. 1759 kN
  3. 1633 kN
  4. 1646 kN
Answer and working

C. 1633 kN

Asc = 4 × π × 20²/4 = 1256.6 mm²; Ac = 122,500 − 1256.6 = 121243.4 mm². Pu = 0.4 × 25 × 121243 + 0.67 × 500 × 1256.6 = 1633 kN. Using the gross area for concrete gives 1646; using 0.87 fy gives 1759; 1823 uses the pure-axial coefficients without the code's allowance for minimum eccentricity.

Question 8 · easy

What is the main purpose of a north-light (saw-tooth) roof truss in a workshop or packhouse?

  1. To increase natural ventilation by forming a ridge vent over the span
  2. To carry crane loads without any internal columns over long spans
  3. To admit even daylight through glazing that faces away from direct sun
  4. To shed heavy snow from both slopes equally in cold climates
Answer and working

C. To admit even daylight through glazing that faces away from direct sun

The steep glazed face is turned towards the pole (north in the northern hemisphere) to admit diffuse daylight without glare or solar heat gain. It is not primarily a snow, crane or ventilation device.

Question 9 · medium

How does a rise of the water table to the base of a shallow footing in sand affect its bearing capacity?

  1. It reduces it only for clays, because sands drain freely and their strength is not affected
  2. It reduces it, because the submerged unit weight, close to half the bulk value, enters the γ terms
  3. It has no effect, because the bearing capacity factors depend only on the angle of shearing resistance
  4. It increases it, because water pressure supports part of the footing load and reduces settlement
Answer and working

B. It reduces it, because the submerged unit weight, close to half the bulk value, enters the γ terms

Effective stresses fall when soil is submerged; the γ in the Nγ term (and in the Nq term if the water rises above the base) is replaced by the submerged unit weight, cutting capacity, especially in cohesionless soils whose strength is purely frictional.

Question 10 · easy

What is the purpose of the earnest money deposit (bid security) submitted with a tender?

  1. To cover defects that appear during the defects liability period after completion
  2. To pay the contractor in advance for mobilising equipment to the site after award
  3. To pay liquidated damages if the completed work is handed over after the due date
  4. To guarantee that the bidder will not withdraw its bid and will sign the contract if it is accepted
Answer and working

D. To guarantee that the bidder will not withdraw its bid and will sign the contract if it is accepted

Bid security protects the owner during tendering; it is returned to unsuccessful bidders. After award, a performance security and retention money cover completion and defects; liquidated damages are deducted from payments. Amounts are set by local procurement rules.

A study plan for Building Materials, Theory of Structures & Construction in Nepal Engineering Council Registration Exam

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (44% of the 78 questions): Estimation, costing and rate analysis (13, 17%); Bricks, stone and cement (12, 15%); Specifications and contracts (9, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Concrete and concrete mix design (8, 10%); Foundations (8, 10%); Reinforced concrete beams and slabs (8, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Reinforced concrete columns (8, 10%); Steel and timber (6, 8%); Trusses (6, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Estimation, costing and rate analysis (6 hard of 13), Foundations (2 hard of 8), Reinforced concrete beams and slabs (2 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Specifications and contracts (5 easy of 9); Bricks, stone and cement (6 easy of 12).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Nepal Engineering Council Registration Exam Building Materials, Theory of Structures & Con

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.