LAISHA
Open Laisha

ICAR AIEEA-PG Farm Power Sources: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
64written to this exam in this subject
8syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Power Sources in ICAR AIEEA-PG

Unit V farm machinery and power with renewable energy: characteristics of human, animal, mechanical and electrical sources, harness types, biogas plant types, gasifier types, biodiesel; Unit II electric motors: induction motor speed, slip, input and output power, starters.

Where the energy for farm work comes from, how much is available, and how mechanisation is measured.

Our 64 ICAR AIEEA-PG questions in this subject: 27 easy, 29 medium, 8 hard, across 8 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

When a worker does hard physical work, most of the metabolic energy released from food appears as:

  1. Useful mechanical work
  2. Waste heat
  3. Stored chemical energy in muscle
  4. Electrical energy in nerves
Answer and working

B. Waste heat

Gross mechanical efficiency of human work is only about 20–25% at best, so roughly three-quarters or more of the metabolic energy becomes heat. This is why heat and humidity limit how long a person can work hard. That heat must be lost to the surroundings.

Question 2 · medium

Which statement about human power output and duration is correct?

  1. The power a person can sustain falls steeply as the duration of effort increases
  2. Human power output stays constant for any duration up to a full 8-hour working day
  3. Peak power over a few seconds is lower than the power that can be sustained all day
  4. Power output rises with ambient temperature above 35 °C
Answer and working

A. The power a person can sustain falls steeply as the duration of effort increases

A person can produce several hundred watts or more for seconds but only about 75 W or less all day. Output is not constant, peak exceeds sustained power, and heat above body-comfort levels reduces output.

Question 3 · easy

A pair of bullocks exerts a steady pull of 1.2 kN while walking at 3 km/h. What power do they develop?

  1. 1.00 kW
  2. 3.60 kW
  3. 12.96 kW
  4. 10.0 kW
Answer and working

A. 1.00 kW

v = 3/3.6 = 0.833 m/s; P = 1.2 kN × 0.833 m/s = 1.00 kW. Multiplying by km/h without converting gives 3.60 kW, the commonest slip. 12.96 kW multiplies by 3.6 instead of dividing (1.2 × 3 × 3.6); 10.0 kW is a factor-of-ten slip.

Question 4 · medium

An animal-drawn mouldboard plough cuts a furrow 20 cm wide and 12 cm deep in a soil with a specific draught of 4 N/cm². What is the draught?

  1. 96 N
  2. 960 N
  3. 9600 N
  4. 480 N
Answer and working

B. 960 N

Draught = specific draught × furrow area = 4 N/cm² × (20 × 12) cm² = 960 N. The other options are decimal slips or half the area; always multiply width by depth in the same units as the specific draught.

Question 5 · medium

Why do diesel (compression-ignition) engines, rather than petrol engines, power nearly all tractors?

  1. Higher compression ratio gives higher thermal efficiency and good low-speed torque
  2. They need no fuel injection system
  3. They are lighter per kW than petrol engines, so the tractor compacts the soil less
  4. They run at higher speeds than petrol engines, giving more power per litre of displacement
Answer and working

A. Higher compression ratio gives higher thermal efficiency and good low-speed torque

Diesel engines use high compression ratios, giving higher thermal efficiency, and deliver high torque at low speed, suited to heavy continuous farm loads. They are heavier and slower-running than petrol engines and depend on fuel injection.

Question 6 · easy

Which motor is the standard choice for farm pumps, threshers and grinders where a three-phase supply is available?

  1. DC series motor
  2. Universal motor
  3. Synchronous motor with DC excitation
  4. Three-phase squirrel-cage induction motor
Answer and working

D. Three-phase squirrel-cage induction motor

The squirrel-cage induction motor is robust, cheap and nearly maintenance-free. DC series and universal motors are for traction and small hand tools; synchronous motors are for special constant-speed or power-factor duties.

Question 7 · medium

Compared with a diesel engine of the same output for a tubewell, which is a genuine disadvantage of an electric motor?

  1. It depends on the hours, voltage and reliability of the grid supply at a fixed point
  2. It has a lower efficiency at the point of use than a diesel engine of the same rated output
  3. It needs frequent oil changes and decarbonising
  4. It cannot be started without a hand crank
Answer and working

A. It depends on the hours, voltage and reliability of the grid supply at a fixed point

Electric motors are more efficient at the point of use, need little maintenance and start instantly. Their weakness is dependence on a supply point and on the quality and hours of rural supply.

Question 8 · medium

At a hot, elevated site the air density is 1.10 kg/m³ instead of the standard 1.225 kg/m³. By how much is the power in the wind reduced at the same wind speed?

  1. 27.6%
  2. 11.4%
  3. 19.4%
  4. 10.2%
Answer and working

D. 10.2%

Power is proportional to density: 1.10/1.225 = 0.8980, a reduction of 10.2%. Cubing the density ratio applies the speed rule to density (27.6%); 11.4% uses the wrong base. 19.4% squares the density ratio (1 − 0.898²).

Question 9 · easy

A farm has 8 cattle each giving 10 kg of fresh dung per day. Taking a gas yield of 0.04 m³ per kg of fresh dung, what daily biogas production can be expected?

  1. 0.32 m³/day
  2. 32 m³/day
  3. 3.2 m³/day
  4. 0.4 m³/day
Answer and working

C. 3.2 m³/day

Dung = 8 × 10 = 80 kg/day; gas = 80 × 0.04 = 3.2 m³/day. 0.4 m³ is for one animal only. 0.32 and 32 m³/day are factor-of-ten slips.

Question 10 · hard

The same 80 kg/day of dung is mixed 1:1 with water (slurry density about 1000 kg/m³). For a hydraulic retention time of 40 days, what digester volume is needed?

  1. 3.2 m³
  2. 6.4 m³
  3. 0.16 m³
  4. 64 m³
Answer and working

B. 6.4 m³

Slurry = 80 + 80 = 160 kg/day ≈ 0.16 m³/day; volume = 0.16 × 40 = 6.4 m³. Forgetting the water gives 3.2 m³; 0.16 m³ is one day's feed only. 64 m³ is a factor-of-ten slip.

A study plan for Farm Power Sources in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 64 questions): Animal draught power and harnessing (11, 17%); Electrical power on the farm (11, 17%); Biomass and biofuels as power sources (10, 16%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Mechanical power: engines and tractors (8, 13%); Human power and its limits (7, 11%); Solar power as a farm power source (7, 11%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Wind power as a farm power source (6, 9%); Farm power availability (kW/ha) (4, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Mechanical power: engines and tractors (2 hard of 8), Farm power availability (kW/ha) (1 hard of 4), Electrical power on the farm (2 hard of 11).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Human power and its limits (4 easy of 7); Mechanical power: engines and tractors (4 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Farm Power Sources

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.