NCEES FE Other Disciplines · USA · NCEES
Original practice questions written to the published syllabus · not past papersNCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).
Source: ncees.org.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Sensors and transducers, bridge circuits, sampling and ADC resolution, block diagrams, closed-loop transfer functions, steady-state error, stability and first- and second-order response.
Measuring temperature, pressure, flow, force and moisture, logging the data, and controlling processes automatically.
Our 35 NCEES FE Other Disciplines questions in this subject: 6 easy, 24 medium, 5 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.
A flow measurement has three independent uncertainty components: ±0.4%, ±0.3% and ±1.2%. What is the most probable (root-sum-square) combined uncertainty?
D. ±1.3%
Independent uncertainties combine as √(0.4² + 0.3² + 1.2²) = √1.69 = 1.30 ≈ ±1.3%. ±1.9% is the arithmetic (worst-case) sum, 1.69 forgets the square root, and 0.63 is merely the average of the three.
A sensor behaves as a 2.00 V source with 50 kΩ internal resistance. It is read with a voltmeter of 1 MΩ input resistance. What will the voltmeter show?
D. 1.905 V
Loading: the meter forms a divider with the source, so it reads V·Rm/(Rs + Rm) = 2.00 × 1000/1050 = 1.905 V, about 4.8% low. 2.000 V would need an infinite meter resistance; 2.100 V adds the 5% instead of losing it; 1.000 V would be the result only if the two resistances were equal.
An NTC thermistor has R = 10.0 kΩ at 25 °C and β = 3950 K. Using the beta equation, what is its resistance at 50 °C?
A. 3.59 kΩ
R = R0·exp[β(1/T − 1/T0)] with kelvin: 1/323.15 − 1/298.15 = −0.000259 K⁻¹; × 3950 = −1.025; e^that = 0.3588; R = 3.59 kΩ. 27.9 kΩ reverses the sign (an NTC falls in resistance as it warms); 5.00 kΩ assumes resistance halves linearly with doubled Celsius temperature, and 20 kΩ treats it as a PTC.
A type K thermocouple (take 41 µV/°C as constant) on a dryer plenum gives 1.64 mV. The reference junction at the logger terminals is at 25 °C. Estimate the plenum temperature.
C. 65 °C
The emf measures the difference between junctions: 1.64 mV / 0.041 mV/°C = 40 °C above the reference, so T ≈ 40 + 25 = 65 °C. Reporting 40 °C omits cold-junction compensation; 15 °C subtracts it; 29 °C makes a factor-of-ten unit slip before adding 25 °C. In real work, convert the reference temperature to emf and use the standard reference table, because the sensitivity is not exactly constant.
A pump delivery gauge reads 150 kPa and the local atmospheric pressure is 101.3 kPa. What is the absolute pressure?
D. 251.3 kPa
Absolute = gauge + atmospheric = 150 + 101.3 = 251.3 kPa. 48.7 kPa subtracts atmospheric pressure; 150 kPa is the gauge reading itself.
A venturi meter on an irrigation main has a 100 mm inlet and 50 mm throat, with Cd = 0.98. Measured Δp between inlet and throat is 20 kPa on water (ρ = 1000 kg/m³). What is the flow rate?
D. 12.57 L/s
A2 = π(0.05)²/4 = 0.001963 m²; β = 0.5, 1 − β⁴ = 0.9375. Q = Cd A2 √(2Δp/(ρ(1 − β⁴))) = 0.98 × 0.001963 × √(40000/937.5) = 0.01257 m³/s = 12.57 L/s. 12.17 L/s omits the velocity-of-approach factor (1 − β⁴); 50.3 L/s uses the inlet area in place of the throat; 7.82 L/s uses an orifice coefficient of 0.61.
A Pitot-static tube in the inlet duct of a batch grain dryer shows a velocity pressure of 150 Pa. Air density is 1.2 kg/m³. What is the local air velocity?
B. 15.8 m/s
v = √(2Δp/ρ) = √(2 × 150/1.2) = √250 = 15.8 m/s. 250 m/s forgets the square root; 11.2 m/s drops the factor 2; 0.55 m/s uses the density of water.
A quarter-bridge strain-gauge circuit is excited at 10 V. The gauge factor is 2.1 and the strain is 800 µε. What is the approximate bridge output?
A. 4.2 mV
Quarter bridge: Vo ≈ Vs·GF·ε/4 = 10 × 2.1 × 800×10⁻⁶/4 = 0.0042 V = 4.2 mV. 16.8 mV is the full-bridge value, 8.4 mV the half-bridge value; 42 mV is a decimal slip.
A steel hitch link (E = 200 GPa) with a 400 mm² cross-section carries an axial pull of 20 kN. What axial strain will a gauge on it read?
D. 250 µε
σ = F/A = 20 000/400×10⁻⁶ = 50 MPa; ε = σ/E = 50×10⁶/200×10⁹ = 0.000250 = 250 µε. 50 µε confuses the stress number with strain; 2500 and 25 µε are factor-of-ten slips in the area or modulus.
A closed-loop system has the characteristic equation s³ + 2s² + 3s + K = 0. For what range of K is it stable?
C. 0 < K < 6
Routh array: rows s³ (1, 3), s² (2, K), s¹ ((2·3 − K)/2), s⁰ (K). All first-column entries must be positive: 6 − K > 0 and K > 0, so 0 < K < 6. For a cubic with positive coefficients the condition is a2·a1 > a0: 2 × 3 > K.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.