NCEES FE Other Disciplines · USA · NCEES
Original practice questions written to the published syllabus · not past papersNCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).
Source: ncees.org.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
The physics and chemistry behind materials, water, fuels and electronics that later engineering subjects assume.
Our 79 NCEES FE Other Disciplines questions in this subject: 25 easy, 36 medium, 18 hard, across 6 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.
In chlorinating a village water supply that contains some ammonia, why is the dose taken beyond the breakpoint?
C. Beyond it, chloramines are destroyed and added chlorine stays as a free residual
As chlorine is added it first forms chloramines with ammonia; further chlorine destroys them and the residual dips to the breakpoint, after which free chlorine accumulates and keeps protecting the supply. Chlorination does not remove hardness, and calcium chloride is soluble.
A downdraft gasifier runs on maize cobs with air as the gasifying agent. Which gas mixture best describes its producer gas?
A. Mainly N2 with CO and H2, plus CO2 and a little CH4
Partial oxidation with air leaves about half the gas as nitrogen; the combustibles are mainly CO and H2 with a little methane, so the heating value is low. Methane with CO2 and H2S describes biogas from anaerobic digestion; CO2 and water are the products of complete combustion.
What distinguishes the gross (higher) calorific value of a fuel from its net (lower) calorific value?
B. Gross includes the latent heat recovered when the water formed in combustion condenses
The water produced from the fuel's hydrogen (and its moisture) gives up its latent heat only if it condenses. Gross value counts that heat; net value assumes the water leaves as vapour. Constant-volume versus constant-pressure differences are small and are not what the two terms mean.
A coal has C 80%, H 5%, O 6%, S 1% by mass. Using Dulong's formula HCV = [8,080 C + 34,500 (H − O/8) + 2,240 S]/100 kcal/kg, what is its gross calorific value?
D. About 7953 kcal/kg
Available hydrogen = 5 − 6/8 = 4.25%. HCV = (8,080 × 80 + 34,500 × 4.25 + 2,240 × 1)/100 = (646,400 + 146,625 + 2,240)/100 = 7953 kcal/kg. Ignoring the oxygen correction gives 8211; dropping sulphur gives 7930; 7688 is the net value.
A diesel pump-set engine delivers 30 kW brake power at a brake thermal efficiency of 30%. The fuel's net calorific value is 42 MJ/kg. What is its fuel consumption?
A. About 8.57 kg/h
Fuel power = 30/0.30 = 100 kW; fuel flow = 100/42,000 = 0.00238 kg/s × 3,600 = 8.57 kg/h. Multiplying by the efficiency instead of dividing gives 0.77; ignoring efficiency gives 2.57; 2.38 is the flow in g/s mislabelled as kg/h.
A steel tank is half full of water and left standing. Where does differential-aeration corrosion attack most strongly, and why?
C. Just below the waterline, where oxygen is poorer and the metal becomes the anode
Areas with less oxygen become anodic relative to well-aerated areas, which act as cathodes; just below the waterline (and under deposits) the steel corrodes. The well-aerated zone near the surface is the cathode, so it is protected rather than attacked.
Nylon-6,6 is formed from which pair of monomers, and by what type of polymerisation?
A. Hexamethylenediamine and adipic acid, by condensation with loss of water
Nylon-6,6 is a polyamide from hexamethylenediamine (six carbons) and adipic acid (six carbons), each amide link releasing water. Ethylene glycol and terephthalic acid give PET (also by condensation); caprolactam gives nylon-6 by ring-opening; phenol and formaldehyde give a thermosetting resin.
Drip laterals are commonly extruded from which polymer, and why?
B. Linear low-density polyethylene, for its flexibility, toughness and low cost
Laterals must bend, be coiled, resist punctures and cost little, so LLDPE/LDPE blends are standard. Polystyrene is brittle; phenolic resins are thermosets that cannot be heat-welded; unplasticised PVC is rigid and is used for mains, not coiled laterals.
A farm collects empty containers marked with the resin identification code 2. Which polymer are they?
C. High-density polyethylene
The codes are 1 PET, 2 HDPE, 3 PVC, 4 LDPE, 5 PP, 6 PS, 7 other. Pesticide containers and water tanks are commonly HDPE.
Why is open burning of waste PVC pipe and film on a farm especially harmful compared with burning polyethylene?
B. PVC releases hydrogen chloride and chlorinated compounds as well as smoke
PVC contains about 57% chlorine by mass; burning it gives hydrogen chloride and can form chlorinated organic pollutants, in addition to the smoke all plastics give. Clean combustion to CO2 and water is not what happens in an open fire, and methane is not the characteristic product.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.