LAISHA
Open Laisha

GATE — Agricultural Engineering (AG), for dairy engineering aspirants

India · IITs and IISc on rotation · secondary source

93practice questions written to this syllabus
8subjects

What GATE is

GATE — Agricultural Engineering (AG), for dairy engineering aspirants is a postgraduate admission exam run by IITs and IISc on rotation, for candidates in India.

Format

Sections

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose.

Check the current format, eligibility, fees and dates on the official site: gate2026.iitg.ac.in.

How to prepare for GATE

Where our 93 questions for it fall

Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.

  1. Heaviest (72% of the questions): Fluid Flow, Thermodynamics & Heat Transfer in Dairy Plants (30); Instrumentation, Process Control & Automation (22); Dairy Plant Design, Layout & Project Engineering (15).

    Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.

  2. Middle band: Mathematics & Statistics for Dairy Science (6); Engineering Fundamentals for Dairy Technologists (5); Emerging & Non-thermal Dairy Processing (5).

    One pass per subject, then mixed sets across them.

  3. Lighter: Rheology & Texture of Dairy Foods (5); Advanced Dairy Engineering (5).

    Definitions, classifications and standard figures; quick to revise, easy marks to lose.

  4. Hardest share: Engineering Fundamentals for Dairy Technologists (3 hard of 5), Rheology & Texture of Dairy Foods (2 hard of 5), Dairy Plant Design, Layout & Project Engineering (5 hard of 15).

    Leave untimed time for these and read every explanation, including for the options you rejected.

Official source: gate2026.iitg.ac.in

8 practice questions, worked

Original questions written to this exam's published syllabus and pattern. Not past papers.

1. A hydrostatic level transmitter in a silo was set up for water (1,000 kg/m³). The silo now holds milk of 1,032 kg/m³. If the true milk depth is 5.0 m, what depth does the transmitter show?

  1. About 5.32 m
  2. About 5.16 m
  3. About 5.00 m
  4. About 4.84 m
Answer and working

B. About 5.16 m

Pressure = 1,032 × 9.81 × 5.0; read as water depth: 5.0 × 1,032/1,000 = 5.16 m. 4.84 m divides the wrong way; 5.00 m ignores the density change; 5.32 m doubles the error.

Instrumentation, Process Control & Automation · Pressure, flow and level measurement

2. Milk flows at 12,000 litres per hour through a holding tube of 47.5 mm inside diameter. What is the mean velocity?

  1. About 0.47 m/s
  2. About 1.88 m/s
  3. About 7.52 m/s
  4. About 3.76 m/s
Answer and working

B. About 1.88 m/s

Q = 12,000/3,600,000 = 0.00333 m³/s; area = π × 0.0475²/4 = 0.00177 m²; v = 0.00333/0.00177 = 1.88 m/s. 0.47 m/s leaves the 1/4 out of the area formula; 7.52 m/s uses the radius in place of the diameter; 3.76 m/s is twice the mean, which is the centreline velocity in laminar flow, not the mean.

Dairy Plant Design, Layout & Project Engineering · Equipment sizing and selection

3. Milk flows at 10 m³/h through a pipe of 51 mm internal diameter. What is its mean velocity?

  1. 5.44 m/s
  2. 0.34 m/s
  3. 4895 m/s
  4. 1.36 m/s
Answer and working

D. 1.36 m/s

A = π(0.051)²/4 = 2.04 × 10⁻³ m²; v = (10/3600)/A = 1.36 m/s. Forgetting the /4 in the area gives 0.34.

Fluid Flow, Thermodynamics & Heat Transfer in Dairy Plants · Fluid properties and Bernoulli's equation

4. A thin cylindrical vessel of 1.5 m diameter and 6 mm wall carries an internal pressure of 0.6 MPa. What are the hoop and longitudinal stresses?

  1. 37.5 MPa hoop and 75 MPa longitudinal
  2. 150 MPa hoop and 75 MPa longitudinal
  3. 75 MPa hoop and 37.5 MPa longitudinal
  4. 75 MPa hoop and 75 MPa longitudinal
Answer and working

C. 75 MPa hoop and 37.5 MPa longitudinal

Hoop stress = PD/(2t) = 0.6 × 1,500/(2 × 6) = 75 MPa; longitudinal = PD/(4t) = 37.5 MPa. Swapping them reverses the formulas; 150/75 forgets the factor of 2; equal stresses describe a sphere, not a cylinder.

Dairy Plant Design, Layout & Project Engineering · Pressure vessel design: codes, shells, heads and supports

5. A Pt100 (α = 0.00385 per °C) is wired with two copper leads of 0.5 Ω each in a two-wire circuit. Roughly what error do the leads cause?

  1. About 2.6 °C too low
  2. About 2.6 °C too high
  3. About 0.4 °C too high
  4. About 1.3 °C too high
Answer and working

B. About 2.6 °C too high

Two leads add 1.0 Ω in series; 1.0 ÷ 0.385 Ω/°C ≈ 2.6 °C, and extra resistance reads as higher temperature. 1.3 °C counts one lead only; the error is not low; 0.4 °C uses 0.385 as the answer.

Instrumentation, Process Control & Automation · Temperature measurement: thermocouples, RTDs and recorders

6. A Newtonian whey of viscosity 2.5 mPa·s flows in laminar flow through a 4 mm internal diameter tube 1 m long under a pressure drop of 2 kPa. Using Hagen-Poiseuille, what is the volumetric flow rate?

  1. 80 mL/s
  2. 0.31 mL/s
  3. 1256637 mL/s
  4. 5.0 mL/s
Answer and working

D. 5.0 mL/s

Q = πΔPR⁴/(8ηL) with R = 0.002 m: π × 2,000 × (0.002)⁴ ÷ (8 × 0.0025 × 1) = 5.027e-06 m³/s = 5.0 mL/s. Using the diameter as R gives 16 times too much; dividing again by 16 gives 16 times too little; using R² instead of R⁴ gives a meaningless large value.

Rheology & Texture of Dairy Foods · Viscometers and rheometers

7. A valve with Kv = 8 passes water at a 1.44 bar pressure drop. Using Q = Kv √ΔP, what is the flow?

  1. 11.5 m³/h
  2. 8.0 m³/h
  3. 9.6 m³/h
  4. 6.7 m³/h
Answer and working

C. 9.6 m³/h

Q = 8 × √1.44 = 8 × 1.2 = 9.6 m³/h. 11.5 omits the square root; 6.7 divides by √ΔP; 8.0 ignores the pressure drop.

Instrumentation, Process Control & Automation · Final control elements: valves and drives

8. For laminar flow of milk in a round holding tube, the velocity profile is parabolic. Integrating it over the cross-section shows that the mean velocity equals:

  1. The centreline velocity itself, because flow is uniform
  2. Half of the centreline velocity
  3. About 0.82 of the centreline velocity
  4. Twice the centreline velocity at the wall
Answer and working

B. Half of the centreline velocity

For Hagen–Poiseuille flow, u = u_max(1 − r²/R²); integrating over the area gives a mean of u_max/2. About 0.82 is the ratio for fully turbulent flow, and the velocity at the wall is zero.

Mathematics & Statistics for Dairy Science · Differential and integral calculus

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock all 93 questions — GATE — Agricultural Engineering (AG), for dairy engineering aspirants

US$10 a month · one price worldwide · cancel any time

  • Every practice question for this course, with explanations
  • Timed papers for the exams this course leads to
  • Ask Laisha to explain any topic — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.