GATE — Agricultural Engineering (AG), for dairy engineering aspirants · India · IITs and IISc on rotation
Original practice questions written to the published syllabus · not past papersGATE — Agricultural Engineering (AG), for dairy engineering aspirants is a postgraduate admission exam run by IITs and IISc on rotation, for candidates in India.
Official site: gate2026.iitg.ac.in.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Measuring and controlling temperature, flow, pressure and level in a milk plant, from sensors to PLC and SCADA.
Our 22 GATE AG questions in this subject: 0 easy, 18 medium, 4 hard, across 7 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE AG and are not shown on any other exam's page.
A first-order temperature probe has a time constant of 5 s. About how long after a step change does it reach 95% of the final change?
D. About 15 s
1 − e^(−t/τ) = 0.95 gives t ≈ 3τ = 15 s. 5 s is one time constant (63.2%), 10 s is two (86.5%) and 25 s is five (about 99.3%).
A thermocouple with an assumed constant Seebeck coefficient of 41 µV/°C has its hot junction at 120 °C and its reference junction at 25 °C. What emf does it produce?
C. About 3.90 mV
emf = 41 µV/°C × (120 − 25) = 3,895 µV ≈ 3.90 mV. 4.92 mV ignores the reference junction; 1.03 mV uses only the reference temperature; 5.95 mV adds the two temperatures.
A Pt100 (α = 0.00385 per °C) is wired with two copper leads of 0.5 Ω each in a two-wire circuit. Roughly what error do the leads cause?
B. About 2.6 °C too high
Two leads add 1.0 Ω in series; 1.0 ÷ 0.385 Ω/°C ≈ 2.6 °C, and extra resistance reads as higher temperature. 1.3 °C counts one lead only; the error is not low; 0.4 °C uses 0.385 as the answer.
An orifice meter shows 40 kPa differential at 20,000 L/h. If the flow falls to 10,000 L/h, what differential will it show?
B. 10 kPa
Flow ∝ √ΔP, so ΔP ∝ flow²: halving flow gives (½)² × 40 = 10 kPa. 20 kPa assumes a linear relation; 5 kPa cubes; 28 kPa takes 40 × 1/√2.
The differential across a venturi falls to one quarter of its earlier value. The flow is now:
C. Half its earlier value
Flow ∝ √ΔP, so √(1/4) = 1/2. A quarter assumes linearity; a sixteenth squares instead of rooting; flow cannot rise when differential falls.
A hydrostatic level transmitter in a silo was set up for water (1,000 kg/m³). The silo now holds milk of 1,032 kg/m³. If the true milk depth is 5.0 m, what depth does the transmitter show?
B. About 5.16 m
Pressure = 1,032 × 9.81 × 5.0; read as water depth: 5.0 × 1,032/1,000 = 5.16 m. 4.84 m divides the wrong way; 5.00 m ignores the density change; 5.32 m doubles the error.
A valve with Kv = 8 passes water at a 1.44 bar pressure drop. Using Q = Kv √ΔP, what is the flow?
C. 9.6 m³/h
Q = 8 × √1.44 = 8 × 1.2 = 9.6 m³/h. 11.5 omits the square root; 6.7 divides by √ΔP; 8.0 ignores the pressure drop.
A centrifugal CIP pump's speed is reduced by 20% with a variable-frequency drive. By the affinity laws, roughly what saving in shaft power results?
A. About 49%
Power ∝ speed³: 0.8³ = 0.512, a saving of about 49%. 20% assumes power ∝ speed; 36% uses the square law for head; 64% is the head ratio, not a saving.
A 4–20 mA level transmitter is ranged 0–5 m. What current corresponds to 3.5 m?
A. 15.2 mA
I = 4 + 16 × (3.5 ÷ 5) = 15.2 mA. 14.0 mA uses 20 × 0.7; 11.2 mA omits the 4 mA offset; 17.5 mA uses 25 × 0.7.
An HTST pasteuriser gives an average holding time of 16 s at 9,000 L/h. If flow rose to 10,000 L/h with the same holding tube, what would the average holding time be?
D. 14.4 s
Holding time ∝ 1/flow: 16 × 9,000 ÷ 10,000 = 14.4 s. 17.8 s scales the wrong way; 16.0 s ignores the change; 12.8 s subtracts 20%.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.