ICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) · India · NTA for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) is a postgraduate admission exam run by NTA for ICAR, for candidates in India. Computer-based, 2 hours, 120 multiple-choice questions, +4 for a correct answer and −1 for a wrong one (2026 bulletin). One paper per major subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Measuring and controlling temperature, flow, pressure and level in a milk plant, from sensors to PLC and SCADA.
Our 17 ICAR AIEEA-PG questions in this subject: 16 easy, 1 medium, 0 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
A thermometer gives readings that agree closely with each other but are all 0.6 °C above the reference. The instrument is:
A. Precise but not accurate
Close agreement between readings is precision (repeatability); a constant offset from the true value is a lack of accuracy, which calibration corrects. Averaging does not remove a systematic bias.
The change of an instrument's output per unit change of its input is called its:
C. Sensitivity
Sensitivity is output change per unit input, such as millivolts per degree. Resolution is the smallest detectable change, hysteresis the rising–falling difference, and dead band the input range giving no output change.
Which is a systematic rather than a random error?
D. A thermometer pocket too short, so the sensor always reads low
A short pocket causes stem conduction and a consistent low reading, a systematic error that installation or calibration must correct. Noise, reading scatter and turbulence give random variation that averaging reduces.
Why is a three-wire connection used for an RTD read in a bridge?
A. Lead resistances sit in adjacent bridge arms and so cancel
In a three-wire bridge, one lead sits in each adjacent arm, so lead resistance and its temperature changes largely cancel. RTDs need no cold-junction compensation, and the third wire neither doubles sensitivity nor carries a chart signal.
What does the designation Pt100 mean?
A. A platinum element of 100 Ω at 0 °C
Pt100 is a platinum RTD with 100 Ω at 0 °C; at 100 °C it reads about 138.5 Ω. It is a resistance device, not a thermocouple, and has no emf output.
In the regenerator of an HTST pasteuriser, why is pasteurised milk kept at a higher pressure than raw milk?
C. So that any plate leak lets pasteurised milk into raw milk, not the reverse
If a pinhole develops, flow goes from high to low pressure; keeping the pasteurised side higher means safe milk leaks into raw milk, which is then pasteurised. The differential has nothing to do with deaeration, pump power or recorder accuracy.
A pneumatic valve that is spring-closed and opens when air is applied fails in which position?
C. Closed
Air-to-open valves are held shut by the spring, so on loss of air they close. Air-to-close valves fail open; ordinary spring-return valves do not hold mid or last position.
A PLC analogue input on a 4–20 mA loop reads 0.2 mA. This most likely means:
B. A broken wire or failed transmitter
A live zero of 4 mA means any reading well below it signals a fault such as an open circuit. The bottom of the range is 4 mA, not near zero.
If the SCADA computer in a dairy fails, what normally happens to the process?
D. PLCs keep controlling; operators lose screens, alarms and data logging
SCADA supervises; control runs in the PLCs, which carry on. Loss of SCADA removes visibility and records, which is a serious problem, but it does not by itself stop control.
On an HTST pasteuriser, the flow diversion valve sends milk forward only when:
B. The holding-tube outlet temperature is at or above the legal cut-in value
The recorder-controller at the holding-tube outlet decides forward flow; below the cut-out it diverts. Balance-tank level, cooling and homogeniser pressure are not the forward-flow condition.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.