LAISHA
Open Laisha

JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering Basic Electrical & Electronics Engineering: practice questions

JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering · India · IITs (JoSAA counselling)

Original practice questions written to the published syllabus · not past papers
10worked here, free
33written to this exam in this subject
10syllabus units

About JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering

JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering is a university entrance exam run by IITs (JoSAA counselling), for candidates in India. JEE Main, then JEE Advanced, then JoSAA counselling.

Official site: krishijagran.com.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Basic Electrical & Electronics Engineering in JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering

Circuits, power, transformers, electronic devices and safe wiring: what a farm engineer needs before motors and sensors.

Our 33 JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering questions in this subject: 23 easy, 9 medium, 1 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering and are not shown on any other exam's page.

Question 1 · easy

Kirchhoff's current law, that the algebraic sum of currents at a node is zero, is a statement of which principle?

  1. Conservation of electric charge
  2. Ohm's law for linear conductors at constant temperature
  3. Conservation of energy around a closed loop
  4. Conservation of magnetic flux linking a circuit
Answer and working

A. Conservation of electric charge

Charge cannot accumulate at a junction, so what flows in must flow out. Conservation of energy is the basis of Kirchhoff's voltage law, not the current law; Ohm's law relates V and I in one element only.

Question 2 · medium

A simple timer charges a 47 µF capacitor through a 100 kΩ resistor from a DC supply. What is the time constant, and roughly what fraction of the supply voltage has the capacitor reached after one time constant?

  1. 4.7 s, about 63 %
  2. 23.5 s, about 99 %
  3. 4.7 s, about 37 %
  4. 0.0047 s, about 63 %
Answer and working

A. 4.7 s, about 63 %

τ = RC = 100 × 10³ × 47 × 10⁻⁶ = 4.7 s. After one τ, V = V_s(1 − e⁻¹) = 63 % of V_s. 37 % is what remains to be charged (or the voltage left on a discharging capacitor). 0.0047 s comes from treating kΩ as Ω; 23.5 s is 5τ, when charging is practically complete.

Question 3 · easy

A sinusoidal supply has a peak value of 325 V. What is its RMS value?

  1. 207 V
  2. 162 V
  3. 460 V
  4. 230 V
Answer and working

D. 230 V

V_rms = V_m/√2 = 325/1.414 = 230 V — the familiar 230 V supply. 207 V is the half-cycle average 2V_m/π; 460 V multiplies instead of dividing; 162 V halves the peak, which has no meaning for a sine wave.

Question 4 · easy

What is the form factor (RMS value ÷ half-cycle average value) of a pure sine wave?

  1. 1.111
  2. 0.637
  3. 0.707
  4. 1.414
Answer and working

A. 1.111

Form factor = (V_m/√2)/(2V_m/π) = π/(2√2) = 1.11. 1.414 is the crest (peak) factor; 0.637 is average/peak; 0.707 is RMS/peak.

Question 5 · easy

What is the reactance of a 100 µF capacitor at 50 Hz?

  1. 200 Ω
  2. 31.8 Ω
  3. 0.0314 Ω
  4. 26.5 Ω
Answer and working

B. 31.8 Ω

X_C = 1/(2πfC) = 1/(2π × 50 × 100 × 10⁻⁶) = 31.8 Ω. 0.0314 Ω multiplies instead of dividing; 200 Ω omits 2π; 26.5 Ω is the value at 60 Hz.

Question 6 · easy

Why must a transformer not be connected to a steady DC supply of its rated voltage?

  1. DC produces a rotating flux that drives the core into mechanical vibration
  2. DC cannot pass through copper windings, so the primary current is zero
  3. DC reverses the turns ratio so that the secondary voltage becomes excessive
  4. Steady flux induces no back-EMF, so a large current overheats the primary
Answer and working

D. Steady flux induces no back-EMF, so a large current overheats the primary

Transformer action needs changing flux. With steady DC there is no induced back-EMF, so the primary current is limited only by its small resistance and becomes very large, overheating the winding; the secondary sees no voltage once the current is steady. DC flows through copper easily, and it does not rotate the flux or alter the turns ratio.

Question 7 · easy

Which impurity added to pure silicon produces n-type material?

  1. Indium, a trivalent acceptor
  2. Germanium, a tetravalent element
  3. Phosphorus, a pentavalent donor
  4. Boron, a trivalent acceptor
Answer and working

C. Phosphorus, a pentavalent donor

Phosphorus has five valence electrons; four bond with silicon and the fifth is free, so electrons become the majority carriers (n-type). Boron and indium are trivalent acceptors that make p-type; germanium is a semiconductor in its own right and adds no carriers.

Question 8 · easy

What happens to the depletion region of a p–n junction when it is reverse biased?

  1. It widens and the barrier potential increases
  2. It disappears and the diode behaves as a resistor
  3. It narrows and the junction conducts heavily
  4. It is unaffected; only the forward drop changes
Answer and working

A. It widens and the barrier potential increases

Reverse bias pulls majority carriers away from the junction, widening the depletion region and raising the barrier so only a tiny leakage current flows until breakdown. Narrowing and heavy conduction describe forward bias.

Question 9 · medium

An op-amp integrator is fed a constant positive DC input voltage. What does its output do?

  1. It stays at a constant value equal to the input voltage multiplied by RC
  2. It produces a single short spike and then returns to zero
  3. It oscillates as a sine wave at a frequency of 1/(2πRC)
  4. It ramps linearly in the negative direction until it saturates
Answer and working

D. It ramps linearly in the negative direction until it saturates

For the inverting integrator V_out = −(1/RC)∫V_in dt; a constant input gives a linear ramp, negative-going, until the output reaches the rail. A spike is the response of a differentiator to a step; an integrator does not oscillate on its own.

Question 10 · easy

For which inputs is the output of a two-input XOR gate 1?

  1. When the two inputs are different
  2. When at least one input is 1
  3. When both inputs are 0
  4. When both inputs are 1
Answer and working

A. When the two inputs are different

XOR (exclusive OR) is 1 for inputs 01 and 10 only. 'At least one input is 1' describes OR, which also gives 1 for input 11.

A study plan for Basic Electrical & Electronics Engineering in JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (61% of the 33 questions): AC circuits, phasors and power factor (5, 15%); DC circuits and network theorems (5, 15%); Digital logic (5, 15%); Semiconductor devices and rectifiers (5, 15%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: House wiring and earthing (3, 9%); Transformers (3, 9%); Electrical safety (2, 6%); Operational amplifiers (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Single-phase and three-phase supply (2, 6%); Electrical measuring instruments (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Transformers (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: House wiring and earthing (3 easy of 3); Single-phase and three-phase supply (2 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — JEE Advanced → IIT Kharagpur B.Tech Agricultural & Food Engineering Basic Electrical & Ele

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.