LAISHA
Open Laisha

ICAR AICE-JRF/SRF Forest Mensuration: practice questions

ICAR AICE-JRF/SRF (PhD) — Subject 59 Forestry · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
26written to this exam in this subject
13syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Subject 59 Forestry is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 2 hours, 120 MCQs (Part A 20 general; Part B 50 core group; Part C 50 subject), +4 / −1, maximum 480.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Forest Mensuration in ICAR AICE-JRF/SRF

MCQs on measurement methods and their principles, the volume formulas and which solids they fit, volume-table types, biomass measurement, CAI/MAI relationships and inventory concepts.

Measuring single trees, logs and stands: diameter, height, form, volume, biomass and growth, with the instruments and formulas used in the field.

Our 26 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 7 medium, 19 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

A stem cross-section at breast height is clearly elliptical. Compared with the diameter of a circle of equal area, the diameter obtained from a girth tape (girth ÷ π) is:

  1. Slightly smaller, because the tape takes the short axis of the ellipse
  2. Exactly equal, because girth always reflects area for any closed shape
  3. Slightly larger, since an ellipse has a longer perimeter than an equal-area circle
  4. Exactly equal, because girth reflects cross-sectional area for any closed stem shape
Answer and working

C. Slightly larger, since an ellipse has a longer perimeter than an equal-area circle

For a given area the circle has the shortest perimeter, so any non-circular stem has a larger girth than the equal-area circle, and girth ÷ π overestimates the equal-area diameter. The bias is small for mild ellipticity. The claim that girth always reflects area is wrong: perimeter and area are linked exactly only for a circle.

Question 2 · medium

Why is bark percentage of volume taken from local measurements rather than a single standard value?

  1. Bark thickness is fixed for each species, but standards change with timber prices
  2. Bark is always close to one-tenth of volume, but tables round it differently
  3. Bark thickness varies with species, age, tree size, height on the stem and site
  4. Bark is excluded from all volume tables, so no value is ever needed
Answer and working

C. Bark thickness varies with species, age, tree size, height on the stem and site

Bark thickness differs greatly between thick-barked species (many pines, fire-adapted savanna trees) and thin-barked species, and within a tree with age and height. No universal percentage exists; under-bark volume needs local bark data.

Question 3 · medium

For a log shaped as the frustum of a cone, how do Huber's and Smalian's formulas compare with the true volume?

  1. Huber overestimates and Smalian underestimates, both by exactly equal amounts
  2. Both are exact, because a cone frustum has straight sides
  3. Both overestimate, Huber's error being twice Smalian's
  4. Huber underestimates; Smalian overestimates by twice Huber's error
Answer and working

D. Huber underestimates; Smalian overestimates by twice Huber's error

For a cone, cross-sectional area changes with the square of length. Integrating shows Huber's mid-area times length falls short and Smalian's end-area average exceeds the true volume by twice that shortfall. Newton's formula is exact. Straight sides do not make the area linear in length.

Question 4 · hard

Which log is most overestimated by Smalian's formula?

  1. A flared butt log resembling a neiloid frustum
  2. A mid-stem log resembling a paraboloid frustum
  3. A perfectly cylindrical log of uniform diameter
  4. A short log cut from the middle of a cylindrical bole
Answer and working

A. A flared butt log resembling a neiloid frustum

Smalian's formula is exact for cylinders and paraboloids and overestimates cone and, most of all, neiloid frustums, because the large end area dominates the average. Butt logs are therefore measured in shorter sections or by Huber or Newton.

Question 5 · hard

The absolute form factor differs from the breast-height (artificial) form factor in that it:

  1. Uses the diameter at one-tenth of total height as the reference section
  2. Uses under-bark volume and the over-bark basal area of the stump
  3. Uses only the volume and height above breast height, with breast-height basal area
  4. Uses the merchantable height instead of total height and includes the stump
Answer and working

C. Uses only the volume and height above breast height, with breast-height basal area

The absolute form factor takes the part of the tree above breast height, compared with a cylinder of breast-height basal area and height equal to the height above breast height. The diameter at a fixed proportion of total height defines the normal (true) form factor.

Question 6 · hard

Why must a form factor be used with the same definitions under which it was derived?

  1. Its value depends on the reference diameter, the height and the volume definition used
  2. Its value is fixed for each species, but the units used for volume differ between countries
  3. Form factors apply only to conifers, so broadleaf definitions differ
  4. Its value is fixed by the solid of revolution the species resembles
Answer and working

A. Its value depends on the reference diameter, the height and the volume definition used

A form factor is a ratio whose numerator (total, merchantable, over or under bark volume) and denominator (reference diameter and height) must match the use. Real trees are not one geometric solid, and form factors vary with species, age, density and crown length.

Question 7 · hard

A stand has 150 m³/ha of stem volume, basic wood density 0.55 t/m³ and a biomass expansion factor of 1.3. What is its above-ground biomass?

  1. 82.5 t/ha
  2. 63.5 t/ha
  3. 107.2 t/ha
  4. 354.5 t/ha
Answer and working

C. 107.2 t/ha

AGB = V × D × BEF = 150 × 0.55 × 1.3 = 107.2 t/ha. Without the BEF, 82.5 t/ha is stem biomass only; dividing by density gives a meaningless 354.5.

Question 8 · medium

Allometric biomass equations are usually built by:

  1. Measuring dbh only and applying the carbon fraction to stem volume
  2. Weighing standing trees with load cells attached to the main roots
  3. Felling trees, weighing parts fresh and oven-drying subsamples for dry mass
  4. Counting rings on increment cores and multiplying by wood density
Answer and working

C. Felling trees, weighing parts fresh and oven-drying subsamples for dry mass

Destructive sampling is the reference method: trees are felled, separated into stem, branches and foliage (and roots for a subset), weighed fresh, and subsampled for dry-to-fresh ratios. The equation then predicts biomass from dbh and other easy measurements.

Question 9 · hard

In a forest carbon estimate built from inventory data, which choice is often the single largest source of error?

  1. The choice of allometric equation that turns measurements into biomass
  2. The rounding of dbh to the nearest centimetre by the field crews
  3. The use of the ratio 44/12 to convert carbon to carbon dioxide
  4. The number of decimal places kept in the basal area factor
Answer and working

A. The choice of allometric equation that turns measurements into biomass

Comparisons of equations on the same data show that switching between plausible allometric models can change biomass estimates by large percentages, typically more than measurement rounding. The 44/12 ratio is an exact molecular-mass ratio.

Question 10 · hard

On steep ground, an uncorrected angle count made with a simple fixed-angle gauge will:

  1. Overestimate basal area, because more trees appear wider on slopes
  2. Give the correct basal area, because the angle does not depend on slope
  3. Give the correct basal area only for trees uphill of the point
  4. Underestimate basal area, since the effective horizontal angle is too small
Answer and working

D. Underestimate basal area, since the effective horizontal angle is too small

On slopes the line of sight is inclined, so the horizontal distance to a tree is less than the sighting distance; a fixed gauge then excludes some trees that should be in. Slope-correcting relascopes or a corrected BAF remove the bias.

A study plan for Forest Mensuration in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 26 questions): Tree biomass and allometric equations (4, 15%); Angle-count (Bitterlich) sampling and relascopes (3, 12%); Age determination and stem analysis (2, 8%); Basal area and its uses (2, 8%); Diameter and girth measurement: breast height conventions, calipers, tapes (2, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Growth and increment: CAI, MAI and their relationship (2, 8%); Log volume formulas: Huber, Smalian, Newton (2, 8%); Site index and site quality curves (2, 8%); Volume of standing trees: form factor and form quotient (2, 8%); Volume tables: local, general and form-class; construction and use (2, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Bark thickness and crown measurements (1, 4%); Height measurement: principles and hypsometers (1, 4%); Stand measurement: stems per hectare, basal area, top height, stand volume (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Diameter and girth measurement: breast height conventions, calipers, tapes (2 hard of 2), Growth and increment: CAI, MAI and their relationship (2 hard of 2), Site index and site quality curves (2 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Forest Mensuration

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.