LAISHA

From the Laisha Library · Agricultural engineering

When to water, and how much

How much water does a crop really use in a day? The FAO method the world's irrigation engineers use, done with a weather figure, a crop coefficient and a pencil. A tour of Laisha's manual on Irrigation Engineering.

December pulls the world's fields in two directions. South of the equator it is early summer: maize in Brazil, Argentina and southern Africa is growing fast, orchards in Australia, Chile and South Africa are carrying fruit, and the sun is close to its highest. North of it, most fields are resting, winter wheat is barely growing, and the work is planning next season's water. Both halves are asking the same question: how much water does this crop actually use, and when should I put it back?

Laisha's degree manual on Irrigation Engineering answers it the way engineers do worldwide, with a method published by the Food and Agriculture Organization of the United Nations in 1998 as FAO Irrigation and Drainage Paper 56. It sounds technical. The idea underneath is simple enough to do on the back of an envelope.

Step one: how thirsty is the weather?

Start with the weather, not the crop. FAO-56 imagines a reference field: a wide stretch of well-watered green grass, 0.12 metres tall. The water it would lose in a day, through evaporation from the soil and transpiration through its leaves, is called the reference evapotranspiration, written ET₀ and measured in millimetres a day. It depends only on the weather: sunshine, temperature, humidity and wind. FAO recommends one equation for it, the FAO Penman-Monteith equation, as the standard method, because it responds to all four.

You do not have to solve that equation yourself. Many national weather services and irrigation advisory services publish ET₀ every day, and Laisha's weather screen shows evapotranspiration beside the forecast. What matters is the size of the number. On a cool, cloudy day it may be one or two millimetres. On a hot, dry, windy summer day it can be six, eight or more.

Step two: how thirsty is the crop?

A crop is not grass, so FAO-56 multiplies ET₀ by a crop coefficient, Kc, to give the crop's own water use:

Kc changes through the season. A newly sown field is mostly bare soil, so Kc is low; at full canopy and flowering it is at its highest; as the crop matures it falls again. FAO-56 tabulates typical values for a sub-humid climate with moderate wind. For grain maize they are about 0.3 at the start, 1.20 in mid-season and 0.35 to 0.60 at the end, depending on how dry the crop is harvested. For tomato they are about 0.6, 1.15 and 0.7 to 0.9. In very dry, windy places tall crops use a little more, and FAO-56 gives the correction.

Step three: how much can the soil hold?

The soil is the crop's water tank. After a thorough wetting, once the free water has drained away, the soil is at field capacity. At the other end is the wilting point, where roots can no longer pull water out. The water between the two, over the depth the roots reach, is the total available water (TAW). A crop cannot use all of it without stress, so FAO-56 uses a fraction, p, to give the readily available water: RAW = p × TAW. For many crops p is around 0.5, which means you water when about half of the tank is used.

One millimetre of water over one hectare is ten cubic metres, or 10,000 litres. Refilling 77 mm on a hectare is therefore about 770 cubic metres of water reaching the root zone, and more must leave the pump, because no system delivers every drop where the roots are. A well-run drip system loses far less on the way than a flooded furrow, which is why the efficiency of the system matters as much as the arithmetic.

Rain counts, but not all of it

Rain resets the balance only partly. Some runs off, some soaks below the roots, and a light shower on a hot afternoon may wet only the surface. The manual calls the part that stays in the root zone effective rainfall. A field record that adds up each day's ETc, subtracts the effective rain and each irrigation, and shows when the depletion reaches RAW is called a soil water balance. It is the same sum a professional irrigation scheduler runs, written in a notebook.

Check the arithmetic with your hands

A number on paper is only as good as the soil it describes. Before you trust a schedule, dig. The United States Department of Agriculture's Natural Resources Conservation Service publishes a simple feel-and-appearance method: take a handful of soil from the root zone, squeeze it, and compare how it holds together with photographs for each soil texture. With practice it estimates soil moisture well enough to catch a schedule that has drifted. Tensiometers and soil moisture sensors do the same job continuously. Advisers at the University of California suggest pairing them: one at shallow root depth tells you when to start watering, one deeper down tells you when to stop.

Water when the soil says so, not when the calendar says so. The arithmetic tells you when to go and look.

A second example: tomatoes on a sandy loam

Tomatoes are shallower-rooted and less forgiving than maize, and they show it in the numbers. FAO-56 gives tomato a depletion fraction of 0.40, against 0.55 for maize, so the trigger comes sooner. Take a tomato crop at full canopy, with roots working the top 0.7 metres of a sandy loam that holds about 100 mm of available water per metre.

The tomato field needs water twice as often as the maize field, in smaller amounts. That is the pattern for most vegetables, and it is the reason drip irrigation, which can deliver small, frequent doses without wetting the whole field, suits them so well. The figure of 100 mm per metre is an assumption for this example; FAO-56 lists typical available water for each soil texture, and a local soil survey or soil test is better still.

Keeping a water balance for a week

A soil water balance is a running total of how much of the readily available water has been used. Start the day after a full irrigation or a soaking rain, with depletion at zero. Each day, add that day's ETc and subtract any effective rain or irrigation. When the total reaches RAW, it is time to irrigate. Here is a week for the maize field above, with a RAW of 77 mm.

After a week, about half of the readily available water is used, so the next irrigation is still several days away. The rain on day 3 counted for less than it measured, because part of a summer shower runs off or evaporates before it soaks in; the figures here are illustrative, and the manual explains the methods for estimating effective rainfall. A notebook with these seven lines, filled in each evening from a published ET₀, is a real irrigation schedule.

A table to keep: crop coefficients and depletion fractions

These are the FAO-56 standard values for a sub-humid climate with moderate wind. Kc ini is the group value for the crop's family where FAO-56 gives one; Kc ini for any field also depends on how often the soil surface is wetted. Use them as a starting point and adjust with local advice.

Two patterns stand out. Shallow-rooted, sensitive crops such as onion, potato and banana have low depletion fractions, so they must be watered before the soil dries far. Deep-rooted, tough crops such as cotton and sugarcane tolerate a drier root zone. And almost every field crop at full canopy uses more water than the reference grass, which is why the mid-season Kc is above 1.

Water and salt

Every irrigation water carries some dissolved salt, and the crop leaves most of it behind in the soil. Where rain is scarce, salts build up in the root zone unless some extra water is applied now and then to wash them below the roots. Laisha's companion manual on Drainage Engineering calls this the leaching requirement: the smallest extra share of water that keeps root-zone salinity acceptable for the crop. If leaf edges burn on a well-watered crop, or a white crust appears on dry soil, have the water and soil tested for salinity before adding more fertiliser.

What usually goes wrong

Watering on a fixed calendar in a season whose weather is not fixed. Using a mid-season Kc for a young crop, which wastes water early. Ignoring rain that has already refilled the profile. Applying more than the soil can hold, so that the extra drains below the roots and carries fertiliser with it. And on sandy soils, which hold little, applying a big volume rarely instead of a smaller volume often.

Agriculture uses most of the fresh water people take from rivers, lakes and aquifers: 69 percent of all withdrawals worldwide, according to FAO's AQUASTAT. Irrigated land is only about a fifth of the world's cultivated land, yet FAO reckons it gives about two-fifths of all agricultural production. Every millimetre that is matched to what the crop actually uses is water left in the river, the well and the next farmer's field.

Read the full manual

laisha.ai/degrees/agri-engineering/irrigation-engineering

Irrigation Engineering: soil water, FAO-56 evapotranspiration, crop coefficients and scheduling, in eleven chapters.

Laisha Review · Monthly

Get Laisha Review every month — free, by email

One email a month when a new issue is out: a degree manual, a crop from field to harvest, an app inside Laisha, a new Laisha Kids book and one of the world's happiest countries.

We will first email you a link to confirm; nothing is sent until you do. Every email has a one-click unsubscribe link. We use your address only to send the magazine. Privacy

Last updated · How Laisha writes and checks its pages · Report a mistake

Go further with Laisha Smarter

US$10 a month · one price worldwide · cancel any time

  • A dated season plan for your own crop and location
  • Pest and disease alerts as the season moves
  • Ask Laisha about what you read or see in your field — up to 1,000 questions a month
10 days free for every new account, no card.