LAISHA
Open Laisha

ICAR AIEEA-PG Mathematics & Statistics for Dairy Science: practice questions

ICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) · India · NTA for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
42written to this exam in this subject
9syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) is a postgraduate admission exam run by NTA for ICAR, for candidates in India. Computer-based, 2 hours, 120 multiple-choice questions, +4 for a correct answer and −1 for a wrong one (2026 bulletin). One paper per major subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mathematics & Statistics for Dairy Science in ICAR AIEEA-PG

The calculus, differential equations and statistics that dairy engineering problems, kinetics and quality control need.

Our 42 ICAR AIEEA-PG questions in this subject: 6 easy, 32 medium, 4 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

A pasteuriser holding tube is designed with milk in laminar flow at a mean velocity of 0.5 m/s. At what velocity must the fastest particle be assumed to travel when checking the minimum holding time?

  1. 0.5 m/s
  2. 1.0 m/s
  3. 0.25 m/s
  4. 0.61 m/s
Answer and working

B. 1.0 m/s

In laminar flow u_max = 2 × mean = 1.0 m/s, and the fastest particle receives the shortest holding time. 0.61 m/s corresponds to the turbulent ratio (mean ≈ 0.82 u_max); using the mean 0.5 m/s overestimates the holding time.

Question 2 · medium

In thermal process calculation, the F value of a process is obtained by:

  1. Integrating the lethal rate 10^((T − T_ref)/z) over the heating time
  2. Differentiating the temperature with respect to time at the coldest point
  3. Multiplying the peak temperature (in °C) by the total holding time
  4. Averaging the D values measured at each temperature in the profile
Answer and working

A. Integrating the lethal rate 10^((T − T_ref)/z) over the heating time

F = ∫10^((T − T_ref)/z) dt accumulates lethality minute by minute. Peak temperature × time ignores that lethality rises tenfold for each z degrees.

Question 3 · medium

Vitamin C in a flavoured milk is lost by first-order kinetics with k = 0.05 per day. What is its half-life?

  1. 13.9 days
  2. 20.0 days
  3. 46.1 days
  4. 10.0 days
Answer and working

A. 13.9 days

t½ = ln 2/k = 0.693/0.05 = 13.9 days. 1/k = 20 days is the time constant; 2.303/k = 46.1 days is the time for a tenfold fall (the D value).

Question 4 · medium

Newton's law of cooling, applied as a lumped-capacity model, is reasonable when the Biot number is:

  1. Below about 0.1
  2. Above about 10
  3. Exactly 1, at any size
  4. Between 1 and 5 for liquids
Answer and working

A. Below about 0.1

Bi = hL/k_solid compares internal to surface resistance. Below about 0.1 the internal temperature is nearly uniform, so a single temperature describes the body. Large blocks of butter or cheese have high Bi and need conduction models.

Question 5 · medium

A well-mixed 2,000 litre balance tank is flushed with clean water at 500 litres per minute. What fraction of an initial dissolved residue remains after 12 minutes?

  1. 0.050
  2. 0.250
  3. 0.717
  4. 0.000
Answer and working

A. 0.050

τ = V/q = 2000/500 = 4 min. C/C₀ = e^(−t/τ) = e^(−3) = 0.050. Plug-flow thinking (three tank volumes = empty) gives 0; e^(−4/12) inverts the ratio.

Question 6 · medium

Applying one Newton–Raphson step to f(x) = x³ − 2x − 5 from x₀ = 2 gives:

  1. 2.0
  2. 1.9
  3. 2.1
  4. 2.5
Answer and working

C. 2.1

f(2) = 8 − 4 − 5 = −1; f′(x) = 3x² − 2, so f′(2) = 10. x₁ = 2 − (−1)/10 = 2.1. Sign slips give 1.9.

Question 7 · medium

Which statement correctly interprets a 95% confidence interval of 3.42 to 3.58% for the mean fat of a silo?

  1. 95% of intervals built this way, over repeated sampling, contain the true mean
  2. 95% of the individual milk samples from the silo lie between 3.42 and 3.58% fat
  3. There is a 95% chance that the next single sample will fall inside this interval
  4. The true mean fat of the silo is certainly 3.50%, the centre of the interval
Answer and working

A. 95% of intervals built this way, over repeated sampling, contain the true mean

The 95% describes the long-run success of the method. The interval concerns the mean, not individual samples, which spread far more widely.

Question 8 · medium

A sample is drawn from the top of an unstirred milk tank. The resulting error in fat content is best described as:

  1. A random sampling error that disappears when the number of samples is increased
  2. A Type II error, because the test fails to detect a difference that exists
  3. A non-sampling bias error that more replicate samples from the top would not reduce
  4. Negligible, because fat is evenly dispersed in milk at rest for many hours
Answer and working

C. A non-sampling bias error that more replicate samples from the top would not reduce

Cream rises in unstirred milk, so top samples are systematically high in fat. That is bias, which more samples from the same spot do not remove; only mixing does.

Question 9 · medium

A calibration line is A = 0.016 + 0.196C (C in mg/L). A sample reads A = 0.50. What is its concentration?

  1. 2.55 mg/L
  2. 2.63 mg/L
  3. 2.47 mg/L
  4. 0.11 mg/L
Answer and working

C. 2.47 mg/L

C = (A − a)/b = (0.50 − 0.016)/0.196 = 2.47 mg/L. Ignoring the intercept gives 2.55; adding it gives 2.63.

Question 10 · easy

Response surface methodology is used in dairy product development mainly to:

  1. Find factor settings that optimise a curved response with interacting factors
  2. Count colonies on plates more accurately
  3. Replace sensory evaluation with instrumental measurement
  4. Estimate the shelf life of a product from one storage temperature
Answer and working

A. Find factor settings that optimise a curved response with interacting factors

RSM fits a model (usually quadratic) to designed experiments and locates optimum factor levels.

A study plan for Mathematics & Statistics for Dairy Science in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 42 questions): Numerical methods for engineering problems (7, 17%); Ordinary differential equations: first-order kinetics and cooling (7, 17%); Differential and integral calculus (6, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Correlation and regression (5, 12%); Introduction to response surface methodology for product optimisation (5, 12%); Matrices and linear equations (5, 12%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Sampling theory and confidence intervals (4, 10%); Descriptive statistics and probability distributions (2, 5%); Tests of significance: t, chi-square and F (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Correlation and regression (1 hard of 5), Differential and integral calculus (1 hard of 6), Numerical methods for engineering problems (1 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Tests of significance: t, chi-square and F (1 easy of 1); Numerical methods for engineering problems (2 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Mathematics & Statistics for Dairy Science

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.