LAISHA
Open Laisha

ICAR AICE-JRF/SRF Mathematics & Statistics for Dairy Science: practice questions

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
53written to this exam in this subject
10syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mathematics & Statistics for Dairy Science in ICAR AICE-JRF/SRF

The calculus, differential equations and statistics that dairy engineering problems, kinetics and quality control need.

Our 53 ICAR AICE-JRF/SRF questions in this subject: 9 easy, 20 medium, 24 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

Rate constants for whey protein denaturation measured at several temperatures give a straight line when plotted as:

  1. ln k against 1/T, with slope −Eₐ/R
  2. k against T, with slope Eₐ/R
  3. ln k against T in °C, with slope −Eₐ/R
  4. 1/k against ln T, with slope R/Eₐ
Answer and working

A. ln k against 1/T, with slope −Eₐ/R

Arrhenius: ln k = ln A − Eₐ/(RT), linear in 1/T with slope −Eₐ/R (T absolute). Plotting against T itself is not linear over a wide range.

Question 2 · hard

Concentration data from a heating trial give a straight line when 1/C is plotted against time, but curves when ln C is plotted. The reaction order is:

  1. Second order
  2. First order
  3. Zero order
  4. Pseudo-first order
Answer and working

A. Second order

1/C − 1/C₀ = kt is the integrated second-order law. A linear ln C plot would indicate first order; a linear C plot, zero order.

Question 3 · hard

Using Simpson's one-third rule on the lethal rates 0.1, 0.6, 0.9, 0.5 and 0.1 logged at 2 min intervals, the F value is:

  1. 4.20 min
  2. 4.27 min
  3. 6.40 min
  4. 2.20 min
Answer and working

B. 4.27 min

Simpson: (h/3)(y₀ + 4y₁ + 2y₂ + 4y₃ + y₄) = (2/3)(0.1 + 2.4 + 1.8 + 2.0 + 0.1) = (2/3)(6.4) = 4.27 min. The trapezoidal value is 4.20 min; the bare sum 2.20 forgets the h/3 weighting.

Question 4 · medium

Five fat tests read 3.2, 3.4, 3.6, 3.8 and 4.0%. What is the sample standard deviation (divisor n − 1)?

  1. 0.316%
  2. 0.283%
  3. 0.632%
  4. 0.100%
Answer and working

A. 0.316%

Deviations −0.4, −0.2, 0, 0.2, 0.4; sum of squares 0.40; variance 0.40/4 = 0.10; s = √0.10 = 0.316%. Dividing by n gives 0.283%; 0.100 is the variance; 0.632 forgets to divide the sum of squares at all.

Question 5 · hard

Spores are distributed at random (Poisson) at a mean of 0.1 per pack in an aseptically filled batch. What fraction of packs contain at least one spore?

  1. 0.100
  2. 0.905
  3. 0.095
  4. 0.010
Answer and working

C. 0.095

P(0) = e^(−0.1) = 0.905, so P(≥1) = 1 − e^(−0.1) = 0.095. Taking the mean (0.100) as the fraction slightly overestimates because some packs carry two or more spores.

Question 6 · easy

If the sample size used for a confidence interval for a mean is increased from 25 to 100, the width of the interval becomes approximately:

  1. One quarter as wide
  2. Half as wide
  3. Twice as wide
  4. Unchanged
Answer and working

B. Half as wide

Width is proportional to 1/√n; √(100/25) = 2, so the interval halves. One quarter would need a sixteenfold larger sample.

Question 7 · medium

Of 300 farm milk samples, 18 fail an antibiotic screening test. What is the approximate 95% confidence interval for the failure rate?

  1. 5.0% to 7.0%
  2. -40.5% to 52.5%
  3. 3.3% to 8.7%
  4. 3.0% to 9.0%
Answer and working

C. 3.3% to 8.7%

p̂ = 0.06; SE = √(0.06 × 0.94/300) = 0.0137; half-width 1.96 × SE = 0.027, giving 3.3% to 8.7%. Forgetting to divide by n gives an impossible negative lower limit.

Question 8 · hard

In a CRD with 5 replicates per treatment, the error mean square is 2.0 on 16 df and t(0.025, 16) = 2.120. What is the least significant difference at 5%?

  1. 1.34
  2. 1.70
  3. 1.90
  4. 1.75
Answer and working

C. 1.90

LSD = t × √(2 × EMS/r) = 2.120 × √(4/5) = 2.120 × 0.894 = 1.90. Omitting the factor 2 gives 1.34; using z = 1.96 ignores the error df.

Question 9 · medium

For a rotatable central composite design with three factors, the axial distance α is:

  1. 1.414
  2. 1.000
  3. 2.000
  4. 1.682
Answer and working

D. 1.682

α = (2ᵏ)^(1/4) = 8^(0.25) = 1.682. 1.414 applies to two factors; 1.000 gives a face-centred design.

Question 10 · hard

Replicated centre points in a response surface experiment are used to:

  1. Increase the number of factor levels to five
  2. Remove the need for randomisation of the run order
  3. Make the design orthogonal to blocks of days
  4. Estimate pure error and test for curvature and lack of fit
Answer and working

D. Estimate pure error and test for curvature and lack of fit

Replicates at one setting measure pure experimental error, enabling a lack-of-fit test; the centre mean versus factorial mean reveals curvature.

A study plan for Mathematics & Statistics for Dairy Science in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (64% of the 53 questions): Analysis of variance and basic experimental designs (11, 21%); Tests of significance: t, chi-square and F (9, 17%); Descriptive statistics and probability distributions (8, 15%); Introduction to response surface methodology for product optimisation (6, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Correlation and regression (5, 9%); Sampling theory and confidence intervals (5, 9%); Matrices and linear equations (3, 6%); Numerical methods for engineering problems (3, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Ordinary differential equations: first-order kinetics and cooling (2, 4%); Differential and integral calculus (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Numerical methods for engineering problems (3 hard of 3), Ordinary differential equations: first-order kinetics and cooling (2 hard of 2), Differential and integral calculus (1 hard of 1).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Correlation and regression (2 easy of 5); Sampling theory and confidence intervals (2 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Mathematics & Statistics for Dairy Science

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.