LAISHA
Open Laisha

GATE ES Hydrology & Water Resources for Environmental Scientists: practice questions

GATE — Environmental Science and Engineering (ES) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
37written to this exam in this subject
12syllabus units

About GATE ES

GATE — Environmental Science and Engineering (ES) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 subject). MCQ, MSQ and NAT question types with negative marking on MCQ only, as in all GATE papers.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Hydrology & Water Resources for Environmental Scientists in GATE ES

The water cycle, surface and groundwater resources and the hydraulics that GATE ES Section 4 examines. Agricultural engineering already teaches watershed hydrology, groundwater and canal hydraulics to design level (subjects watershed-hydrology and groundwater-wells-pumps); this subject covers what an environmental scientist needs and the environmental framing: water balance, threats to water resources and channel and pipe flow basics.

Our 37 GATE ES questions in this subject: 16 easy, 14 medium, 7 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE ES and are not shown on any other exam's page.

Question 1 · easy

Where is most of the world's fresh water stored?

  1. Rivers and streams
  2. The atmosphere
  3. Ice and snow
  4. Freshwater lakes
Answer and working

C. Ice and snow

About 69% is ice and snow, about 30% groundwater, about 1% surface and other water.

Question 2 · hard

A 3-hour unit hydrograph (for 1 cm) has ordinates [0, 20, 50, 30, 10, 0] m3/s at 3-hour intervals. Effective rainfall is 2.0 cm in the first 3 hours and 1.0 cm in the next 3 hours. What is the peak of the direct runoff hydrograph?

  1. 110 m3/s
  2. 120 m3/s
  3. 100 m3/s
  4. 150 m3/s
Answer and working

B. 120 m3/s

Convolution: DRH = 2 x UH(t) + 1 x UH(t - 3 h); ordinates [0.0, 40.0, 120.0, 110.0, 50.0, 10.0, 0.0]; peak 120. Multiplying the UH peak by 3 cm assumes both blocks peak together; 110 is the next ordinate, not the peak.

Question 3 · easy

The storage in a reservoir below the lowest outlet is called:

  1. Flood storage
  2. Dead storage
  3. Live storage
  4. Surcharge storage
Answer and working

B. Dead storage

Dead storage is unusable by gravity and partly reserved for sediment.

Question 4 · hard

Monthly inflows to a reservoir site are [10, 2, 1, 8, 12, 3, 1, 9] (million m3) and the demand is a constant 6 million m3/month. Using the sequent peak (cumulative deficit) method, what storage is required?

  1. 17 million m3
  2. 9 million m3
  3. 2 million m3
  4. 5 million m3
Answer and working

B. 9 million m3

Running deficit K_t = max(0, K_t-1 + demand - inflow): the maximum is 9. Summing all monthly shortfalls (17) ignores refilling between dry spells.

Question 5 · hard

Using C0 = 0.048, C1 = 0.429, C2 = 0.524, inflows I1 = 30 and I2 = 50 m3/s and outflow O1 = 25 m3/s, what is O2?

  1. 36.0 m3/s
  2. 40.0 m3/s
  3. 15.2 m3/s
  4. 28.3 m3/s
Answer and working

D. 28.3 m3/s

O2 = C0 I2 + C1 I1 + C2 O1 = 2.38 + 12.86 + 13.10 = 28.3. Swapping I1 and I2 gives 36.0.

Question 6 · hard

A well pumps 1,728 m3/day from a confined aquifer. Steady drawdowns are 3.0 m at 10 m and 1.0 m at 100 m. Using Thiem, what is the transmissivity?

  1. 158 m2/day
  2. 633 m2/day
  3. 138 m2/day
  4. 317 m2/day
Answer and working

D. 317 m2/day

T = Q ln(r2/r1) / [2 pi (s1 - s2)] = 1,728 x 2.303 / (2 pi x 2) = 317. Using log10 gives 138.

Question 7 · easy

Water flows at 0.05 m3/s through a pipe of diameter 0.1 m. What is the mean velocity?

  1. 0.50 m/s
  2. 1.59 m/s
  3. 0.00039 m/s
  4. 6.37 m/s
Answer and working

D. 6.37 m/s

V = Q / A = 0.05 / (pi x 0.05^2) = 6.37. Using d instead of d/2 in the area gives 1.59.

Question 8 · medium

A pump delivers 0.1 m3/s against a head of 30 m with efficiency 0.75. What power does it require?

  1. 39.2 kW
  2. 4.0 kW
  3. 22.1 kW
  4. 29.4 kW
Answer and working

A. 39.2 kW

P = rho g Q H / eta = 1,000 x 9.81 x 0.1 x 30 / 0.75 = 39.2 kW.

Question 9 · easy

Minimum specific energy in a rectangular channel equals:

  1. 1.5 times critical depth
  2. Critical depth
  3. 0.5 times critical depth
  4. 2 times critical depth
Answer and working

A. 1.5 times critical depth

E_min = 1.5 y_c. At this minimum the flow is critical, with Froude number 1.

Question 10 · hard

A venturi meter (inlet 0.3 m, throat 0.15 m diameter, Cd = 0.98) shows a differential head of 0.5 m of water. What is the discharge?

  1. 0.0542 m3/s
  2. 0.0396 m3/s
  3. 0.0560 m3/s
  4. 0.0343 m3/s
Answer and working

C. 0.0560 m3/s

Q = Cd A1 A2 sqrt(2gh)/sqrt(A1^2 - A2^2) = 0.0560. Ignoring the approach-velocity term or using Cd = 0.6 gives the others.

A study plan for Hydrology & Water Resources for Environmental Scientists in GATE ES

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (38% of the 37 questions): Continuity, momentum and energy equations; pipe flow and pipe networks (4, 11%); Open-channel flow: specific energy, critical flow, hydraulic jump (4, 11%); Aquifers: confined, unconfined, porosity, transmissivity, storage (3, 8%); Darcy's law and steady-state well hydraulics (3, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Flow measurement in pipes and channels (3, 8%); Fluid properties, hydrostatics, buoyancy (3, 8%); Hydrographs and the unit hydrograph (3, 8%); Precipitation, infiltration, evapotranspiration and runoff (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Reservoir and channel routing (3, 8%); Stage-discharge relationships and reservoir capacity (3, 8%); The hydrological cycle and water balance (3, 8%); Global water resources: distribution, quality and threats (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Darcy's law and steady-state well hydraulics (1 hard of 3), Flow measurement in pipes and channels (1 hard of 3), Fluid properties, hydrostatics, buoyancy (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Aquifers: confined, unconfined, porosity, transmissivity, storage (2 easy of 3); Precipitation, infiltration, evapotranspiration and runoff (2 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE ES Hydrology & Water Resources for Environmental Scientists

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.