Indian Forest Service Examination Wood Products & Forest-Based Industries: practice questions
Indian Forest Service Examination (IFoS) — Forestry optional · India · Union Public Service Commission
Original practice questions written to the published syllabus · not past papers
10worked here, free
39written to this exam in this subject
10syllabus units
About Indian Forest Service Examination
Indian Forest Service Examination (IFoS) — Forestry optional is a government recruitment exam run by Union Public Service Commission, for candidates in India. Three stages: the Civil Services (Preliminary) Examination as a screening test; a written Main examination of six conventional papers (General English 300, General Knowledge 300, and two optional subjects of two papers each at 200 marks, 1,400 in all); and a 300-mark personality test.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Wood Products & Forest-Based Industries in Indian Forest Service Examination
Turning wood into products: sawmilling, veneer and plywood, panels and engineered wood, pulp and paper, wood energy and the chemistry of wood-based industries.
Our 39 Indian Forest Service Examination questions in this subject: 8 easy, 21 medium, 10 hard, across 10 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Indian Forest Service Examination and are not shown on any other exam's page.
Question 1 · medium
Quarter-sawn boards, compared with flat-sawn boards:
Shrink more in width and cup more
Have lower recovery and no figure in any species
Shrink less in width and cup less
Cannot be dried in kilns
Answer and working
C. Shrink less in width and cup less
Faces are radial; recovery is lower and sawing slower.
Question 2 · hard
Why is saw maintenance by a saw doctor important for recovery?
It increases the diameter of the logs delivered
It adds preservative to every board sawn
It reduces the need for grading the output
Straighter, thinner cuts
Answer and working
D. Straighter, thinner cuts
Accurate sawing needs less oversize and planing allowance.
Question 3 · medium
Phenol-formaldehyde adhesives are used for:
Interior plywood only, kept dry
Paper sizing
Pellet binding
Exterior and marine plywood
Answer and working
D. Exterior and marine plywood
PF bonds resist boiling water; UF is for interior use.
Question 4 · hard
Reconstituted panels are important for forest use mainly because they:
Use thinnings, residues and recycled wood
Require large, clear, high-grade logs
Need durable species
Use only bamboo
Answer and working
A. Use thinnings, residues and recycled wood
Small and low-grade material becomes useful panels.
Question 5 · easy
Softwood fibres are commonly about how long?
0.3 mm
3 mm
30 mm
3 cm
Answer and working
B. 3 mm
Hardwood fibres are about 1 mm.
Question 6 · easy
Oven-dry wood has a net calorific value of 19 MJ/kg. Using NCV(wet) = NCV(dry)(1 − w) − 2.44w, what is the net value at 30% wet-basis moisture?
Like an oil refinery using all fractions of crude.
Question 8 · medium
In India, the code of practice for design of structural timber is:
IS 303
IS 401
IS 710
IS 883
Answer and working
D. IS 883
The National Building Code 2016 also covers timber and bamboo.
Question 9 · medium
Timber should be dried before installation in buildings mainly to:
Increase its weight for stability
Make it combustible
Limit movement after installation
Change its species
Answer and working
C. Limit movement after installation
Drying to service MC prevents shrinkage gaps and distortion.
Question 10 · medium
Which tool quantifies the environmental impacts of building materials over their life?
Life-cycle assessment
Bucking optimisation software
Prong test
Janka test
Answer and working
A. Life-cycle assessment
LCA and environmental product declarations compare materials.
A study plan for Wood Products & Forest-Based Industries in Indian Forest Service Examination
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (44% of the 39 questions): Wood energy: fuelwood, charcoal, pellets (5, 13%); Engineered wood: glulam, LVL, cross-laminated timber (4, 10%); Particleboard, fibreboard (MDF) and oriented strand board (4, 10%); Pulp and paper: raw materials, pulping processes (4, 10%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Timber in construction and its standards (4, 10%); Veneer and plywood manufacture (4, 10%); Wood chemistry and extractives (4, 10%); Wood-based industries: raw-material supply and residues (4, 10%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Chain of custody and legality in wood supply (3, 8%); Sawmilling and recovery (3, 8%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Chain of custody and legality in wood supply (1 hard of 3), Sawmilling and recovery (1 hard of 3), Engineered wood: glulam, LVL, cross-laminated timber (1 hard of 4).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Particleboard, fibreboard (MDF) and oriented strand board (2 easy of 4); Pulp and paper: raw materials, pulping processes (2 easy of 4).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.