ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Unit V farm machinery and power: definitions (anthropometry, static and dynamic dimensions, percentiles), work physiology terms (VO2max, heart rate, cardiac cost), noise and vibration basics, ROPS and safety devices, and women-friendly tools. Mostly recall with short calculations.
Designing machines around the people who use them, and measuring the noise, vibration and work load they face.
Our 43 ICAR AIEEA-PG questions in this subject: 35 easy, 8 medium, 0 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
The stature of a group of farm workers is normally distributed with mean 1640 mm and standard deviation 58 mm. The 95th percentile stature is closest to
D. 1735 mm
X95 = mean + 1.645 × SD = 1640 + 1.645 × 58 = 1735.4 mm. Mean + 1 SD (1698 mm) is only the 84th percentile; 1545 mm is the 5th percentile; z = 1.96 (1754 mm) is the 97.5th percentile, a common slip from two-sided confidence intervals.
The minimum clearance between a tractor steering wheel and the seat (thigh clearance) should be designed for
A. a large user, typically the 95th percentile of the larger user group
A clearance must accommodate the biggest users, so it is set for a high percentile of the larger group. Designing for the average leaves half the users cramped; the 5th percentile principle applies to reaches, not clearances.
The distance from the seat to a frequently used hydraulic control lever should be designed so that it can be reached by
B. a small operator, typically the 5th percentile of the smaller group
If the small user can reach the lever, everyone larger can too. Using the 95th or 50th percentile would leave small users, often women, unable to reach without leaving the seat.
Measurement of the maximum forward reach of a seated operator while operating a lever is an example of
A. dynamic (functional) anthropometry
Functional dimensions are measured while the body performs a movement. Static anthropometry measures the body in a fixed standard posture, for example sitting height.
The anthropometric dimension that primarily determines seat height is
B. popliteal height
Seat height is set from the floor-to-underside-of-thigh (popliteal) height so the feet rest flat without pressure under the thighs. Sitting height sets backrest and head clearance; hip breadth sets seat width.
Foot-operated controls such as the tractor clutch and brakes are preferred over hand controls when
B. large forces are needed while the hands are busy steering
Legs deliver larger forces and free the hands. Precise positioning is better done by hand.
Using the classification very light < 90, light 90–105, moderately heavy 105–120, heavy 120–135, very heavy 135–150 and extremely heavy > 150 beats/min, a task with an average working heart rate of 128 beats/min is
C. heavy
128 lies in the 120–135 band, which is heavy. Students sometimes subtract resting heart rate first; this classification uses the working heart rate itself.
The Borg rating of perceived exertion (RPE) scale commonly used in field ergonomics runs from
D. 6 to 20
The original Borg RPE scale runs 6–20, roughly one-tenth of heart rate in young adults. Category-ratio scales run 0–10. 1 to 5 is a short rating scale, not the Borg RPE.
The seated human body is most sensitive to vertical whole-body vibration in the frequency range of about
B. 4–8 Hz
Trunk and abdominal resonance lie roughly in 4–8 Hz, close to tractor ride frequencies. Below 0.5 Hz motion sickness dominates; 50–100 Hz and above are hand-arm and audio ranges.
A roll-over protective structure on a tractor protects the operator effectively only if
A. the seat belt is worn
The belt keeps the operator inside the clearance zone; an unbelted operator can be thrown out and crushed by the tractor or the ROPS itself.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.