LAISHA
Open Laisha

GATE Human Engineering, Ergonomics & Safety: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
37written to this exam in this subject
8syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Human Engineering, Ergonomics & Safety in GATE

Human engineering and safety in the Farm Power section: numerical questions on adding decibel levels, change of level with distance or number of sources, noise dose, vibration transmissibility, natural frequency and damping ratio from logarithmic decrement, rms acceleration, anthropometric percentiles from mean and SD, and energy expenditure from oxygen uptake or heart rate. NAT answers are sensitive to using 10 log versus 20 log and rms versus peak.

Designing machines around the people who use them, and measuring the noise, vibration and work load they face.

Our 37 GATE questions in this subject: 8 easy, 18 medium, 11 hard, across 8 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

Popliteal height of a female worker population has mean 420 mm and SD 24 mm. The 5th percentile value, used for the lowest seat-height setting, is

  1. 459.5 mm
  2. 380.5 mm
  3. 373.0 mm
  4. 396.0 mm
Answer and working

B. 380.5 mm

X5 = 420 − 1.645 × 24 = 380.5 mm. Mean − SD (396 mm) is the 16th percentile; 459.5 mm is the 95th; z = 1.96 gives the 2.5th percentile (373.0 mm).

Question 2 · medium

A tractor seat height adjustment is intended to fit most of a mixed male and female user population. The range usually specified is

  1. the 50th percentile male value with no adjustment
  2. from the 5th to 95th percentile of male workers only, ignoring female popliteal height
  3. from the 50th percentile female to the 50th percentile male, with a fixed shoe allowance
  4. from the 5th percentile female to 95th percentile male popliteal height, plus shoes
Answer and working

D. from the 5th percentile female to 95th percentile male popliteal height, plus shoes

An adjustable range is designed to cover the small end of the smaller group and the large end of the larger group. The male-only range excludes many women; a fixed average fits nobody well.

Question 3 · easy

A tractor operator must identify the hydraulic lift lever by touch without looking at it. The most suitable coding method is

  1. labelling
  2. coding by the colour of the adjacent panel
  3. shape coding
  4. colour coding
Answer and working

C. shape coding

Shape (and texture or size) can be felt through gloves without looking. Colour and labels need vision and good lighting.

Question 4 · medium

Increasing the control-response (C/R) ratio of a control, other things equal,

  1. speeds gross movement but worsens fine adjustment
  2. has no effect on positioning time
  3. speeds gross movement and improves fine adjustment at the same time
  4. improves fine adjustment but slows gross movement to a target
Answer and working

D. improves fine adjustment but slows gross movement to a target

A high C/R ratio means large control movement for small response: slow travel, precise final positioning. A low ratio gives fast travel but overshoot. Total time is minimised at an intermediate ratio.

Question 5 · hard

A worker's average energy expenditure is 25 kJ/min. Using Murrell's formula (S = 5 kcal/min, resting 1.5 kcal/min), the rest required in each 60-minute period is about

  1. 51.1 min
  2. 13.0 min
  3. 0 min
  4. 9.8 min
Answer and working

B. 13.0 min

Convert first: 25 kJ/min ÷ 4.186 = 5.97 kcal/min. R = 60 × (5.97 − 5)/(5.97 − 1.5) = 13.0 min. Putting 25 directly into the kcal formula gives 51.1 min, a unit slip; 0 min would apply only if W ≤ S; dividing by W instead of (W − 1.5) gives 9.8 min.

Question 6 · medium

Three identical pumps each produce 90 dB at the operator's position. With all three running, the level is about

  1. 94.8 dB
  2. 93.0 dB
  3. 99.5 dB
  4. 270.0 dB
Answer and working

A. 94.8 dB

L = 90 + 10 log 3 = 94.77 dB. 93 dB is the two-source answer; 270 is arithmetic addition; 99.5 wrongly uses 20 log 3.

Question 7 · hard

Ten identical chaff cutters in a shed each produce 84 dB at a point. With all ten running, the level is

  1. 87 dB
  2. 840 dB
  3. 104 dB
  4. 94 dB
Answer and working

D. 94 dB

L = 84 + 10 log 10 = 94 dB. 87 is the two-source result; 104 uses 20 log 10; 840 is arithmetic addition.

Question 8 · hard

A seat with natural frequency 2 Hz and damping ratio 0.2 is excited by floor vibration at 4 Hz. The transmissibility is about

  1. 1.28
  2. 0.41
  3. 0.32
  4. 0.33
Answer and working

B. 0.41

r = 4/2 = 2. T = √[1 + (2ζr)²]/√[(1 − r²)² + (2ζr)²] = √(1 + 0.64)/√(9 + 0.64) = 1.2806/3.1048 = 0.412. 0.33 is the undamped value 1/|1 − r²|; 0.32 omits the damping term in the numerator; 1.28 is only the numerator.

Question 9 · hard

At resonance (r = 1), a seat with damping ratio 0.25 has a transmissibility, using the full expression, of about

  1. 2.24
  2. 4.00
  3. 0.50
  4. 2.00
Answer and working

A. 2.24

At r = 1: T = √(1 + (2ζ)²)/(2ζ) = √(1 + 0.25)/0.5 = 2.236. 1/(2ζ) = 2.00 is the small-damping approximation; 1/ζ = 4 and 2ζ = 0.5 are formula slips.

Question 10 · medium

A tractor driver is exposed to a frequency-weighted rms acceleration of 0.8 m/s² for 5 hours a day. The daily exposure A(8) is about

  1. 1.01 m/s²
  2. 0.63 m/s²
  3. 0.50 m/s²
  4. 0.80 m/s²
Answer and working

B. 0.63 m/s²

A(8) = aw √(T/8) = 0.8 × √(5/8) = 0.632 m/s². Linear scaling gives 0.50; ignoring duration gives 0.80; inverting the ratio gives 1.01.

A study plan for Human Engineering, Ergonomics & Safety in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (70% of the 37 questions): Vibration: transmissibility and damping (11, 30%); Noise: decibels and exposure (9, 24%); Work physiology: energy expenditure, heart rate and oxygen uptake (6, 16%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Anthropometry (5, 14%); Design of controls and seats (3, 8%); Dust and thermal stress (1, 3%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Safety standards and ROPS (1, 3%); Tools designed for women workers (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Tools designed for women workers (1 hard of 1), Anthropometry (2 hard of 5), Work physiology: energy expenditure, heart rate and oxygen uptake (2 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Work physiology: energy expenditure, heart rate and oxygen uptake (2 easy of 6); Design of controls and seats (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Human Engineering, Ergonomics & Safety

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.