LAISHA
Open Laisha

ICAR AIEEA-PG Farm Machinery Management & Economics: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
44written to this exam in this subject
11syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery Management & Economics in ICAR AIEEA-PG

Definitions (field efficiency, timeliness, fixed versus variable cost), formulas and short calculations of capacity, cost and depreciation.

Choosing, sizing, costing and replacing machines, and running a custom hiring centre that pays.

Our 44 ICAR AIEEA-PG questions in this subject: 16 easy, 28 medium, 0 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

For the same machine and operator, why is field efficiency usually higher in a long rectangular field than in a short, irregular plot?

  1. Overlap is not needed in rectangular fields
  2. Headland turning time is a smaller share of total time in long fields
  3. Draft is lower in long fields, so the tractor can be driven at a higher speed
  4. Refilling is not required when fields are long
Answer and working

B. Headland turning time is a smaller share of total time in long fields

Turning time per turn is roughly fixed; a long field needs fewer turns per hectare, so productive time is a larger share. Draft, overlap and refilling needs do not depend on field length in this way.

Question 2 · easy

Which cost per hectare falls as the size (width) of a machine increases, other things being equal?

  1. Annual insurance and housing
  2. Operator labour cost
  3. Interest on the purchase price
  4. Annual depreciation charge
Answer and working

B. Operator labour cost

A wider machine finishes in fewer hours, so labour (and timeliness) cost per season falls. Depreciation, interest, insurance and housing all rise with the higher price of a bigger machine.

Question 3 · medium

A tractor costs 700,000, has a 10-year life and 10 % salvage value. Interest is 11 % and taxes, insurance and housing total 2 % of price per year. It is used 1,000 h per year. What is the fixed cost per hour?

  1. 119.35/h
  2. 122.50/h
  3. 105.35/h
  4. 154.00/h
Answer and working

A. 119.35/h

Depreciation = 630,000/10 = 63,000; interest = (700,000 + 70,000)/2 × 0.11 = 42,350; TIH = 14,000. Total = 119,350; per hour = 119.35. Interest on the full price gives 154.00/h; leaving out TIH gives 105.35/h. 122.50/h ignores salvage in both depreciation and interest (70,000 + 38,500 + 14,000).

Question 4 · medium

In the simple method, interest is charged on (P + S)/2 rather than on P because:

  1. Invested capital falls from P to S over the life, averaging (P + S)/2
  2. Banks charge interest only on half the original loan in the simple method
  3. Only half of the price (P/2) is usually borrowed
  4. Salvage value earns interest at twice the rate
Answer and working

A. Invested capital falls from P to S over the life, averaging (P + S)/2

Assuming straight-line decline, the investment averages (P + S)/2 over the life. The charge is an opportunity cost, whether or not money is borrowed.

Question 5 · medium

An operator is paid 75 per hour. The machine's effective field capacity is 0.5 ha/h, and paid labour hours are 10 % more than machine field hours. What is the labour cost per hectare?

  1. 135/ha
  2. 41.25/ha
  3. 150/ha
  4. 165/ha
Answer and working

D. 165/ha

Machine hours per hectare = 1/0.5 = 2 h; labour hours = 2 × 1.1 = 2.2 h; cost = 2.2 × 75 = 165 per hectare. 150 omits the allowance; 41.25 multiplies by capacity instead of dividing. 135 deducts the 10 % instead of adding it (2 × 0.9 × 75).

Question 6 · easy

What is the annual rate used in double-declining-balance depreciation for a machine with an 8-year life?

  1. 12.5 %
  2. 18.75 %
  3. 25 %
  4. 20 %
Answer and working

C. 25 %

Double-declining rate = 2/L = 2/8 = 25 % of the opening book value. 12.5 % is the straight-line rate 1/L; 20 % would be the rate for a 10-year life. 18.75 % is the 150 % declining-balance rate (1.5/8).

Question 7 · medium

If the custom-hire rate for an operation rises while the owner's costs stay the same, the break-even use for ownership:

  1. Is unchanged, since it depends only on fixed cost
  2. Falls to a smaller area
  3. Rises, so ownership needs a larger area
  4. Becomes zero, so ownership always pays
Answer and working

B. Falls to a smaller area

x* = FC/(R − VC). A larger R increases the denominator and lowers x*. It never reaches zero while FC > 0. So ownership pays at a smaller area than before.

Question 8 · easy

The economic life of a machine is the age at which:

  1. Its annual repair cost first equals its original purchase price
  2. Its average annual cost of ownership and operation is lowest
  3. Its book value reaches zero
  4. It can no longer be repaired
Answer and working

B. Its average annual cost of ownership and operation is lowest

Economic life minimises average annual cost. A machine can often still be repaired well after that age, and book value depends on the accounting method.

Question 9 · medium

While ploughing, a two-wheel-drive tractor shows 30 % wheel slip. What is the most appropriate first action?

  1. Add ballast or reduce the draft load until slip falls into the recommended range
  2. Lower tyre pressure below the minimum rating
  3. Remove ballast to lighten the tractor
  4. Increase engine speed to spin the wheels faster
Answer and working

A. Add ballast or reduce the draft load until slip falls into the recommended range

30 % slip wastes power and wears tyres; more weight on the driving wheels or a lighter load reduces it. Removing ballast would raise slip further. Too little slip, on the other hand, signals excess ballast.

Question 10 · medium

India's scheme launched in 2018 for Punjab, Haryana, Uttar Pradesh and Delhi subsidised straw-management machines mainly to:

  1. Increase wheat yields through deeper ploughing
  2. Reduce burning of paddy straw by managing it in the field
  3. Replace combines with manual harvesting
  4. Promote drones for spraying
Answer and working

B. Reduce burning of paddy straw by managing it in the field

The in-situ crop residue management scheme supports machines that chop, spread or incorporate paddy straw, or sow wheat into it, so farmers need not burn residue before wheat sowing.

A study plan for Farm Machinery Management & Economics in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 44 questions): Depreciation methods: straight line, declining balance, sum-of-years digits (7, 16%); Fixed costs: depreciation, interest, taxes, insurance and housing (7, 16%); Break-even use and custom-hire comparison (4, 9%); Field efficiency and timeliness (4, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Replacement decisions (4, 9%); Theoretical and effective field capacity (4, 9%); Tractor-implement matching (4, 9%); Variable costs: repair and maintenance, fuel and labour (4, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Mechanisation policy and subsidies (3, 7%); Machinery selection and sizing (2, 5%); Custom hiring centre economics (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Mechanisation policy and subsidies (2 easy of 3); Replacement decisions (2 easy of 4).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Farm Machinery Management & Economics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.