LAISHA
Open Laisha

NCEES PE Agricultural and Biological Engineering Engineering Drawing, Graphics & CAD: practice questions

NCEES PE Agricultural and Biological Engineering · USA · NCEES (ASABE is the content partner)

Original practice questions written to the published syllabus · not past papers
10worked here, free
38written to this exam in this subject
7syllabus units

About NCEES PE Agricultural and Biological Engineering

NCEES PE Agricultural and Biological Engineering is a licensing and registration exam run by NCEES (ASABE is the content partner), for candidates in USA. Computer-based, 85 questions, 9.5-hour appointment (8.5 hours of exam). Once a year (next: 28 Oct 2026). Closed book with the electronic NCEES handbook and supplied searchable ASABE standards; SI and US customary units.

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Drawing, Graphics & CAD in NCEES PE Agricultural and Biological Engineering

Graphics, CAD and GIS appear under Common System Applications. Expect to interpret drawings and plans rather than draw: reading orthographic and sectional views, scales on plans, dimensioning and tolerance stack-up, limits and fits, weld symbols in the AWS convention, and the use of CAD models for quantities and checks. Third-angle projection and ASME Y14.5 conventions are the US default.

Reading and making drawings of machine parts and buildings, by hand and in CAD.

Our 38 NCEES PE Agricultural and Biological Engineering questions in this subject: 3 easy, 15 medium, 20 hard, across 7 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES PE Agricultural and Biological Engineering and are not shown on any other exam's page.

Question 1 · hard

The end projectors of a line are 40 mm apart along XY. In the front view the ends differ in height by 30 mm, and in the top view they differ in distance from the VP by 50 mm. What is the true length of the line?

  1. 120.0 mm
  2. 70.7 mm
  3. 50.0 mm
  4. 64.0 mm
Answer and working

B. 70.7 mm

The three differences are mutually perpendicular, so TL = √(40² + 30² + 50²) = √5000 = 70.7 mm. 64.0 mm is only the top-view length and 50.0 mm only the front-view length; 120 mm adds the components arithmetically.

Question 2 · medium

On a shaft drawing, the overall length of 200 mm is shown in parentheses as (200), while the individual step lengths are dimensioned and toleranced. What does the parenthesised dimension mean?

  1. It is the most critical dimension and must be inspected on every part
  2. It is a theoretically exact dimension that locates a geometric tolerance zone
  3. It is a dimension that may be changed by the machinist to suit the stock
  4. An auxiliary dimension, for information only and not toleranced
Answer and working

D. An auxiliary dimension, for information only and not toleranced

Parentheses mark an auxiliary (reference) dimension, which duplicates information derivable from other dimensions and carries no tolerance. A theoretically exact dimension is shown in a rectangular box, not in parentheses.

Question 3 · medium

A hole is 25.000–25.021 mm and its shaft is 24.980–24.993 mm. What are the maximum and minimum clearances?

  1. 0.041 mm and 0.007 mm
  2. 0.028 mm and 0.020 mm
  3. 0.020 mm and 0.007 mm
  4. 0.041 mm and 0.028 mm
Answer and working

A. 0.041 mm and 0.007 mm

Maximum clearance = largest hole − smallest shaft = 25.021 − 24.980 = 0.041 mm. Minimum clearance = smallest hole − largest shaft = 25.000 − 24.993 = 0.007 mm. Pairing largest with largest or smallest with smallest gives intermediate values, not the extremes. Both clearances are positive, so this is a clearance fit. Largest hole − largest shaft gives 0.028 mm, and smallest hole − smallest shaft gives 0.020 mm.

Question 4 · hard

A hole is 30.000–30.021 mm and a shaft is 30.002–30.015 mm. Classify the fit and give its extreme values.

  1. Clearance; maximum clearance 0.019 mm, minimum clearance -0.002 mm
  2. Transition; maximum clearance 0.006 mm, maximum interference 0.002 mm
  3. Interference; maximum interference 0.015 mm, minimum interference 0.002 mm
  4. Transition; maximum clearance 0.019 mm, maximum interference 0.015 mm
Answer and working

D. Transition; maximum clearance 0.019 mm, maximum interference 0.015 mm

Largest hole − smallest shaft = 30.021 − 30.002 = +0.019 mm (clearance possible). Smallest hole − largest shaft = 30.000 − 30.015 = −0.015 mm (interference possible). Either can occur, so it is a transition fit. Calling it a clearance fit ignores that the largest shaft exceeds the smallest hole.

Question 5 · medium

Why is the hole-basis system of fits more common than the shaft-basis system in general machine work?

  1. Holes are made with fixed-size reamers and plug gauges, so fixing hole limits saves tooling
  2. International standards forbid the shaft-basis system for parts above 10 mm diameter
  3. The hole-basis system always gives interference fits, which are stronger in service
  4. Shafts cannot be ground accurately, so their size must be allowed to vary over a wide range
Answer and working

A. Holes are made with fixed-size reamers and plug gauges, so fixing hole limits saves tooling

Keeping the hole at H means a small set of reamers and gauges serves many fits, while shafts are easily turned or ground to any size. The shaft-basis system is permitted and is used, for example, when one drawn shaft carries several parts with different fits.

Question 6 · hard

In an isometric drawing, an engineer measures a line parallel to one of the axes and finds it to be 40 mm, but the line is not drawn to the isometric scale. What true length does it represent?

  1. 49.0 mm, because all isometric lines are foreshortened
  2. It cannot be found, because no lines in an isometric drawing are measurable
  3. 32.7 mm, because isometric drawings always use the isometric scale
  4. 40 mm, because an isometric drawing uses true lengths along the axes
Answer and working

D. 40 mm, because an isometric drawing uses true lengths along the axes

An isometric drawing (as opposed to projection) is drawn with full lengths on isometric lines, so an isometric line of 40 mm represents 40 mm. Only non-isometric lines cannot be measured. Correcting by 0.816 would apply only to an isometric projection.

Question 7 · medium

For a hole of size 10.0–10.2 mm with a position tolerance of ⌀0.1 at MMC, what is the virtual condition, i.e. the largest fixed pin that will always pass through?

  1. 9.9 mm
  2. 10.0 mm
  3. 10.3 mm
  4. 10.1 mm
Answer and working

A. 9.9 mm

Virtual condition of an internal feature at MMC = MMC − geometric tolerance = 10.0 − 0.1 = 9.9 mm. 10.1 mm adds the tolerance as for an external feature; 10.0 mm ignores the position error. 10.3 mm adds the tolerance to the largest hole size.

Question 8 · medium

Under the 3-2-1 principle, how many points of contact establish the primary, secondary and tertiary datums?

  1. Three, three and three
  2. One, two and three
  3. Two, two and two
  4. Three, two and one
Answer and working

D. Three, two and one

The primary datum plane is set by three points, the secondary by two and the tertiary by one, removing all six degrees of freedom. Reversing the order would leave the part unstable on its primary face.

Question 9 · hard

On a weld symbol, a small circle is drawn where the arrow line meets the reference line, together with a fillet triangle. What does it mean?

  1. Spot weld of circular shape at the arrow point
  2. Fillet weld all round the joint, as for a tube welded to a plate
  3. Fillet weld made in the field rather than in the shop
  4. Fillet weld to be finished flush by grinding
Answer and working

B. Fillet weld all round the joint, as for a tube welded to a plate

The circle at the junction means weld all round. A field weld uses a flag; flush finishing uses a contour symbol; a spot weld has its own circular elementary symbol placed on the reference line.

Question 10 · hard

A datum feature symbol is attached to the large flat face on which a gearbox cover seats. Why is this face usually chosen as the primary datum?

  1. It is the largest face, and GD&T always requires the largest face to be primary
  2. It is the easiest face to paint, so it will be visible to inspectors
  3. It is the face with the finest surface finish, which alone defines datums
  4. It is the functional seating face that locates the part in assembly
Answer and working

D. It is the functional seating face that locates the part in assembly

Datums should reflect function: the seating face establishes the plane on which the part sits. Size, paint or finish do not decide datum choice, although a functional face is often also large and machined.

A study plan for Engineering Drawing, Graphics & CAD in NCEES PE Agricultural and Biological Engineering

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (74% of the 38 questions): Geometric dimensioning and tolerancing basics (11, 29%); Dimensioning and tolerances (10, 26%); Orthographic projection (7, 18%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: 2D and 3D CAD modelling (4, 11%); Fasteners and their drawing (4, 11%); Isometric projection (1, 3%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Sectional views (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Isometric projection (1 hard of 1), 2D and 3D CAD modelling (3 hard of 4), Geometric dimensioning and tolerancing basics (6 hard of 11).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Geometric dimensioning and tolerancing basics (2 easy of 11); Orthographic projection (1 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES PE Agricultural and Biological Engineering Engineering Drawing, Graphics & CAD

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.