GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papersGATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.
Source: gate2026.iitg.ac.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Section 4 names flow of Newtonian fluids and heat transfer; Section 1 names starch gelatinisation and retrogradation. Rheology and physical properties appear as the inputs to flow and heat-transfer calculations (viscosity, power-law parameters, thermal properties) and in reasoning about starch and gel behaviour.
Measuring and modelling how foods flow, deform, break and transfer heat: rheometry of fluids and gels, viscoelasticity, texture profile analysis, and thermal, electrical and optical properties. Agricultural Engineering's engineering-properties-biomaterials covers size, shape, density and friction of grains and produce; this subject goes deeper into processed foods and their measurement.
Our 30 GATE XE questions in this subject: 7 easy, 16 medium, 7 hard, across 7 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE XE and are not shown on any other exam's page.
Porosity strongly lowers the thermal conductivity of a dry food mainly because
D. air in the pores conducts heat very poorly
Air (about 0.025 W/m K) is a good insulator, so porous foods conduct poorly.
Shear rates in the mouth during swallowing of liquids are commonly quoted as around
A. 50 s⁻¹
About 50 s⁻¹ is often used for sensory thickness, though values vary; 10⁻⁶ s⁻¹ is sedimentation and 10⁵ s⁻¹ homogenisation.
A power-law fluid with n = 1 is
C. Newtonian
With n = 1, τ = Kγ̇ and K equals the viscosity.
On a log–log plot of shear stress against shear rate for a power-law fluid, the slope equals
A. the flow behaviour index n
log τ = log K + n log γ̇: slope n, intercept log K.
Mayonnaise holds its shape on a spoon but spreads under a knife. The model that best describes it is
D. Herschel–Bulkley
A yield stress plus shear-thinning above it is Herschel–Bulkley.
The yield stress of a sauce is best measured without wall-slip errors using
B. a vane geometry rotated slowly
The vane shears within the sample, avoiding slip at smooth walls and disturbing the structure little.
In an Ostwald viscometer, water (998 kg/m³, 1.00 mPa s) flows in 60 s and a syrup (1,200 kg/m³) in 300 s. The syrup's viscosity is closest to
D. 6.0 mPa s
μs = μw (ρs ts)/(ρw tw) = 1.00 × (1,200 × 300)/(998 × 60) = 6.0 mPa s. 5.0 ignores densities; 4.2 inverts the density ratio; 7.2 uses 1,200/1,000 × 300/50.
In the farinograph, water absorption is the amount of water needed to bring the dough consistency peak to
A. 500 Brabender units
The 500 BU line is the standard reference consistency.
A flour with a low falling number most likely
A. came from sprouted, high-amylase wheat
High α-amylase liquefies the gelatinised paste so the plunger falls quickly; malt is added to raise activity when the falling number is high.
Using P = 2πfε0ε″E² with f = 2.45 GHz, ε0 = 8.854 × 10⁻¹² F/m, ε″ = 15 and E = 1,000 V/m, the power absorbed per unit volume is closest to
C. 2.04 × 10⁶ W/m³
P = 2π × 2.45 × 10⁹ × 8.854 × 10⁻¹² × 15 × 10⁶ = 2.04 × 10⁶ W/m³. Omitting 2π gives 3.25 × 10⁵; using E instead of E² gives a value 1,000 times smaller; 1.06 × 10⁷ uses the dielectric constant ε′ (about 78) instead of the loss factor ε″.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.