LAISHA
Open Laisha

GATE XE Cereal Science & Milling Technology: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
28written to this exam in this subject
12syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Cereal Science & Milling Technology in GATE XE

Section 3 names milling of rice, wheat and maize, parboiling and waste utilisation from rice milling. Expect MCQs and NATs on kernel structure, extraction rate, tempering water, head rice yield, parboiling effects, wet milling products, rice bran stabilisation and husk utilisation.

The structure and chemistry of cereal grains and millets and how they are milled into flour, semolina, rice and maize products, with the flour quality tests that decide what each flour can make.

Our 28 GATE XE questions in this subject: 13 easy, 11 medium, 4 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · easy

Durum wheat, used for semolina and pasta, is:

  1. Hexaploid and soft
  2. Diploid and waxy
  3. Hexaploid and red-grained only
  4. Tetraploid and very hard
Answer and working

D. Tetraploid and very hard

Triticum durum is tetraploid, very hard and has yellow endosperm; bread wheat is hexaploid.

Question 2 · easy

The main purpose of conditioning (tempering) wheat before milling is to:

  1. Toughen the bran and mellow the endosperm for clean separation
  2. Kill insects and moulds on the grain
  3. Bleach the endosperm to a whiter colour
  4. Raise the protein content of the flour
Answer and working

A. Toughen the bran and mellow the endosperm for clean separation

Tough bran stays in large flakes; friable endosperm separates cleanly.

Question 3 · medium

Why does parboiling increase head rice yield?

  1. Gelatinised starch seals cracks and hardens the grain
  2. Soaking dissolves the brittle outer endosperm
  3. Steaming removes the husk without any milling
  4. Drying makes the grain softer and more flexible
Answer and working

A. Gelatinised starch seals cracks and hardens the grain

Gelatinisation fills fissures; the grain becomes harder and resists breakage.

Question 4 · hard

Glucose isomerase is used in starch processing to:

  1. Saccharify dextrins to glucose
  2. Cross-link starch chains for stability
  3. Convert glucose to fructose
  4. Liquefy gelatinised starch into dextrins
Answer and working

C. Convert glucose to fructose

α-Amylase liquefies; glucoamylase saccharifies; glucose isomerase isomerises.

Question 5 · easy

The three main stages of malting are:

  1. Mashing, boiling and fermenting
  2. Tempering, breaking and reduction
  3. Steeping, germination and kilning
  4. Soaking, steaming and drying
Answer and working

C. Steeping, germination and kilning

Soaking, steaming, drying is parboiling; mashing and boiling belong to brewing.

Question 6 · medium

Pearl millet flour turns rancid quickly after milling mainly because:

  1. Its relatively high fat meets active lipase on grinding
  2. It absorbs moisture faster than other flours
  3. Its protein ferments in the presence of air
  4. Its starch retrogrades rapidly at room temperature
Answer and working

A. Its relatively high fat meets active lipase on grinding

Heat treatment or decortication extends shelf life.

Question 7 · easy

Rice bran must be stabilised soon after milling mainly to prevent:

  1. Free fatty acid formation
  2. Growth of Clostridium botulinum
  3. Loss of protein by evaporation
  4. Gelatinisation of the bran starch
Answer and working

A. Free fatty acid formation

Lipase acting on bran oil makes it bitter and costly to refine.

Question 8 · medium

Rice bran with germ makes up about what share of paddy?

  1. 20–25%
  2. 8–10%
  3. 1–2%
  4. 35–40%
Answer and working

B. 8–10%

Husk is about 20%; bran with germ about 8–10%.

Question 9 · easy

Pregelatinised starch is useful in instant foods because it:

  1. Needs boiling to thicken
  2. Contains no amylopectin
  3. Swells in cold water
  4. Is cross-linked with phosphate
Answer and working

C. Swells in cold water

It has been cooked and dried, so it thickens without heating.

Question 10 · easy

Which step comes last in the traditional corn flake process?

  1. Flaking
  2. Tempering
  3. Cooking
  4. Toasting
Answer and working

D. Toasting

Grits are cooked, dried, tempered, flaked and then toasted.

A study plan for Cereal Science & Milling Technology in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 28 questions): Rice milling and parboiling: quality and by-products (4, 14%); Wheat milling: conditioning, break, reduction and flour streams (4, 14%); Dry and wet milling of maize; starch, syrups and germ oil (3, 11%); Flour quality: protein, gluten, falling number and ash (3, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Rice bran stabilisation and by-product utilisation (3, 11%); Structure and composition of wheat, rice, maize, barley, oats, sorghum and millets (3, 11%); Breakfast cereals and instant cereal products (2, 7%); Millet processing and products (2, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Dough rheology tests: farinograph, mixograph, extensograph and alveograph (1, 4%); Malting of barley and other grains (1, 4%); Oat milling and beta-glucans (1, 4%); Starch modification: physical, chemical and enzymatic (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Dry and wet milling of maize; starch, syrups and germ oil (1 hard of 3), Flour quality: protein, gluten, falling number and ash (1 hard of 3), Rice milling and parboiling: quality and by-products (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Dough rheology tests: farinograph, mixograph, extensograph and alveograph (1 easy of 1); Malting of barley and other grains (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Cereal Science & Milling Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.